|
| BenJ |
|
||
|
ashcook wrote: BenJ wrote: ashcook wrote: How much room above the mixer to the bonnet? Plenty. In reality, the bracket used is from the left hand side so the height is the same, but it sits a tiny bit further forward. Still has adequate clearance. BenJ Great, that's excellent! Doh, I was talking about the convertor. The mixer sits a bit lower than the convertor, so has plenty of clearance. BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| snap0964 |
|
|||
|
The converter to mixer gas hose is very short in this setup - around 5".
This should improve the response we hope, along with the 50 CFM better air flow with the 225 mixer over the 200 (which is normally used in the gas BBM setups). Normally the hose runs from LHS to RHS of the car in an Impco 200 mixer setup.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| BenJ |
|
||
|
Done.
The LPG is now operational. Oh, and had to add some bling to make it functional.     Seems to drive ok. Have only been up the road and back, so will give more feedback late. Cheers BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride Last edited by BenJ on Thu Jul 09, 2009 3:11 pm, edited 1 time in total. |
||
| Top | |
||
| TROYMAN |
|
||
|
that looks like a pretty good set up there ben...
the only thing i would have a little concern about is the heat from the extractors effecting the convertor to mixer hose and the rubber flex hose? otherwise i think you should get better results than the previous set up.. 
|
||
| Top | |
||
| Froudey |
|
||
|
that intake isn't hitting on the bbm is it?
looks very neat and tidy
_________________ R.I.P Tobias my son. |
||
| Top | |
||
| BenJ |
|
||
|
TROYMAN
I am yet to look at a heat shield of some sort. That will be next on the list. Froudey I would actually say it is 'sitting' on the BBM. I am considering some sort of bracket to lift it a little, using the EL intake bolt holes. The intake setup is only temporary until I get together with Da22le, and we design a 'Petrol Bypass' setup. Oh, and the other bit I forgot, was the Crankcase Ventilation. I have just got back from Bunnings with a couple of barbs to work out a solution. Cheers BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| huggiebear |
|
|||
|
looks damn good ben, have you thought about just a mini air filter for the rockercover?
|
|||
| Top | |
|||
| LP_ |
|
||
|
BenJ wrote: Oh, and the other bit I forgot, was the Crankcase Ventilation. Not after being reminded  huggiebear wrote: looks damn good ben, have you thought about just a mini air filter for the rockercover? That solution sounds good but I believe it has to interface with the intake before the mixer due to the hazardous gases emitted |
||
| Top | |
||
| huggiebear |
|
|||
|
but a few boosted guys run a filter... just a thought tho
|
|||
| Top | |
|||
| BenJ |
|
||
|
Actually, I believe it needs to be plumbed into the intake for emmissions purposes.
Not a bad idea though. BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| LP_ |
|
||
|
Crankcase Ventilation is now plumbed into the intake
|
||
| Top | |
||
| fiend |
|
|||
|
Find the EVLUTE character and swap diff's --- He needs the 3.23:1 more than you! Guess your 5 speed is the newer model with the taller fifth gear then, as mine has 3.23:1 like yours, and no way would I go to anything less in the diff department. Rev's are high enough at 110km/h for my liking.
Anyway, all this is my rather confused way of asking "What's the story with the 1673?" Going to turn that gas setup into a real fire breather?! Last edited by fiend on Sat Jul 04, 2009 10:27 am, edited 1 time in total. |
|||
| Top | |
|||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
benJ as much as i hate gas on a falcon, that setup actually looks pretty cool...... well done
|
||
| Top | |
||
| XR-Lane |
|
|||
|
Good to see the gas set up finally with the BBM. Are those Boxcar throttle body piping on front and back of the mixer? Good work, very neat and tidy as always.
Josh Last edited by XR-Lane on Sat Jul 04, 2009 10:25 pm, edited 1 time in total. |
|||
| Top | |
|||
| frankieh |
|
|||
|
That's a bloody huge mixer.... I love it... got any spares ??? mine is in the rubber EL intake knuckle and it's tiny...
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 6 guests |
