Fordmods Logo

My EF Futura, FG XR6 and Stacer 399 PA 

 

Page 1 of 5 [ 69 posts ] Go to page 1, 2, 3, 4, 5  Next

 
 Post subject: My EF Futura, FG XR6 and Stacer 399 PA
Posted: Sun Jun 05, 2011 4:30 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

Hi all,

Thought I’d introduce myself and my trusty EF Futura.
It’s a 1996 6 cylinder EF Futura, Factory 5 speed. I bought it for $2500 off EBay to replace my 1995 EF GLI Auto. It was advertised as in excellent mechanical condition with a few dents, so I got in the car and had a squiz but never drove or opened the bonnet even (should have).

When I picked it up I was told the clutch needed to be put to the floor and that it was a “common Ford thing” only to find out it was the dreaded firewall failure (bodgied up with a G clamp??). $600 later it was repaired.
I also had to change the Clutch (Exedy HD – From a crap PBR), Rotors (DBA Slotted), Wheel bearings, Rack, Lifters, Muffler, Tyres, Reset the Koni rear shocks and install new top rubbers, Straitened rear springs (were hanging over the saddles), remove the crap bubbled tint, replace the dodgy Extractor gasket, rocker gasket, ISC and much more! s**t! :x

Now im rebuilding an engine for it from a wreck I purchased and stripped. :P
I stripped it down, the block was taken to a machinist where I had the following works done:
*Block: Acid dipped, decked .010, bored .020, line bored & new welsh plugs.
*Crank: Cleaned, checked for cracks, 10/10 grind and polish.
*Head: Cleaned, straitened, shaved, a minor pocket port & a general recon.
*Got new .020 cast pistons (not planning on massive revs or boost...yet). Gasket set with AU steel head gasket, New timing chain, guides and tentioner.

I have also bought a new water pump, head dowels, Hastings chrome moly ring set.

I still need to get a new water outlet base, high volume oil pump, Belts, plugs and s**t. I am hoping to have it in and running by the end of July 2011.

Regards,
Ryan.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Last edited by EFFUTURA4.05SP on Thu Aug 22, 2013 10:34 pm, edited 2 times in total.

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 7:15 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

Well I have my ADSL now.

BUT I CANT UPLOAD THE DAMN PICS!!!!

Can anyone shed some light here???????????????

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 9:45 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

My EF!!!

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 9:46 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

AAAARRGGGG!!! Im gunna crack a hissy fit soon!!!!

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 9:50 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

This is what I found after taking off the head...
Looks pretty ordinary

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 9:54 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

Strip Down

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 9:56 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

After Machining and new pistons were fitted by yours truly

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 9:58 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

After some candy blue enamel

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 10:02 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

How it now lies...

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 10:07 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

My current Donk!
Looks are decieving...Rings are shot :(

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 10:25 pm 
Getting Side Ways
Offline
User avatar

Age: 38

Posts: 622

Joined: 24th May 2007

Gallery: 9 images

Ride: 97 TICKFORD XR6 Manaul

Location: Aldinga Beach
SA, Australia

coming along nicely mate

like the colour of your new engine that blue is awersome
Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Mon Jun 06, 2011 11:25 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

Its Holts duplicolour metalcast. Heavy metalic base with a candy blue top coat.
Had a chat to thier chemist and he said it is fine for engines. comes in red and purple too.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Tue Jun 07, 2011 7:20 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

WTF?? Random much?

Are you spruiking your EBay ad?

Sorry, But I have a whole car of spares in my shed from an EF Fututa a stripped a while back (as per post above) Unless you have an EF or EL XR6 front end or a Turbo Kit for me....

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Sun Jun 12, 2011 8:17 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

I sprayed the dash with stuff from around the shed.
I used some plastic adhesion primer then some high-fill and I used septone guide coat black for colour!

I was bored so I thought why not But had to do it twice because I sanded through when I was cutting it back So it is REALLY shiny...

Pics:

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
 
 Post subject: Re: My EF futura thread and new engine build!
Posted: Sun Jun 12, 2011 8:20 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 591

Joined: 28th May 2011

Gallery: 4 images

Ride: EF Futura DUH

Location: central coast
NSW, Australia

Ignore the shotty carpet. That will be replaced soon I hope

You do not have the required permissions to view the files attached to this post.

 

_________________

1996 EF Futura factory manual
Fully rebuilt engine,Decked, Honed, Bored, Tolerences spot on, Wade 1673, Extractors, 2.5" zorst, 3" CAI, High flow filter, Exedy sports tuff clutch, Chiptorque tune.
Future Mods: A mortgage...

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 5  [ 69 posts ]  Go to page 1, 2, 3, 4, 5  Next

Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Mon Nov 25, 2024 7:21 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names