|
| velcro |
|
||
|
The chrome trim on my eb fairmont has started to look like crap so I have ordered in some new stuff.
Now I have no idea how this stuff is held on and how you replace it? I asume it just peels off and the new stuff will stick on? Does anyone have any advice. Thanks |
||
| Top | |
||
| RustyEF |
|
||
|
Hey quick reply for you, umm you ahev to take the otehrone off and scrape of the double sided tape of the bar if possible, and witht he new one it shoudl coem with double sided tape on ti already, but if not just buy some from anywhere? safeway everywhere sells it, and lay it on easy as 1,2,3
CHEERS RUSTY
_________________ -------EL Fairmont Ghia with CUstome BA XR body kit------- |
||
| Top | |
||
| velcro |
|
||
|
Thanks alot for the fast reply. Sounds alot easier then I thought
|
||
| Top | |
||
| BOON250 |
|
||
|
any ideas on doing the chrome on the doors which is part of the moulding???
|
||
| Top | |
||
| Mohekn |
|
||
|
what about that spray adhesive? would that do the job? or would that ruin it all?
_________________ Buy my car |
||
| Top | |
||
| madmax |
|
|||
|
BOON250 wrote: any ideas on doing the chrome on the doors which is part of the moulding???
IIRC the EA-ED chrome on the door moulding is part of the moulding and cannot be replaced.
_________________
|
|||
| Top | |
|||
| velcro |
|
||
|
What about the chrome just infront of the front door? is that part of the moulding? or replacable?
|
||
| Top | |
||
| madmax |
|
|||
|
velcro wrote: What about the chrome just infront of the front door? is that part of the moulding? or replacable?
The little piece on the guard? Isn't it the same as the door moulding?
_________________
|
|||
| Top | |
|||
| velcro |
|
||
|
mmm yeah it is
So anyone got any idea's on replacing the door trim. I've seen people with different trim on there doors before. It must be possible. |
||
| Top | |
||
| madmax |
|
|||
|
velcro wrote: mmm yeah it is
So anyone got any idea's on replacing the door trim. I've seen people with different trim on there doors before. It must be possible. You have to replace the whole moulding. Unfortunately they are no longer made for most of the older E series, so finding them is difficult. A mate has replaced all but 1 on his NC, can't get a LH rear door moulding anywhere.
_________________
|
|||
| Top | |
|||
| velcro |
|
||
|
I mean I have seen people with like pink, blue etc moulding on the doors. Indicating you must be able to pull off the old stuff somehow?
|
||
| Top | |
||
| dalesf150 |
|
|||
|
they probebly just masked and painted the coloured ones
_________________ If mistakes are the best way to learn why the hell arn't I a freekin genius yet.
|
|||
| Top | |
|||
| Mitch_ |
|
|||
Posts: 6168 Joined: 5th Nov 2004 |
how much did it cost you...and wouldnt u be able to use the stuff of the new series for the doors, cause i thought the doors were the same thruout the e-series, the only differecnt being cosmetic....
_________________
|
|||
| Top | |
|||
| madmax |
|
|||
|
mitch_anderson wrote: how much did it cost you...and wouldnt u be able to use the stuff of the new series for the doors, cause i thought the doors were the same thruout the e-series, the only differecnt being cosmetic....
Yes you could use the later model mouldings, it would be a very expensive option though, several hundred dollars for all the trims
_________________
|
|||
| Top | |
|||
| velcro |
|
||
|
The trim for the front bumper cost $22
I was hoping I would also be able to use it on the sides. But ah well. Will check out the wreckers. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 38 guests |
cause i just bought a BA XR6 
