|
| MAD |
|
|||||
|
I've just checked mine, and it is definitely the right wire colours you've got.
On mine the pink/black has 12V with the ign to 'on' The pink/black was the thickest of the pink wires. You could check the wire continuity from the engine plug to the gearbox, and also bridge the connection on the other half to test the rest to the lights. The pins you're looking for are 140 and 140 both R-BK (according to the diagram, yes both the same number)
|
|||||
| Top | |
|||||
| Falcon96XR6 |
|
|||
|
Ran the live wire and all is well and good, reverse lights on in reverse, and off in neutral,
Now i want to know.. can i temporarily do the dodgy and run the live wire to it for a few days till i can put it over the pit? Would it affect anything?
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| MAD |
|
|||
|
It should be fine, but at least put a fuse at the battery.
And don't park the car and leave it in reverse. |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
{USERNAME} wrote: It should be fine, but at least put a fuse at the battery. And don't park the car and leave it in reverse. Okay mate, sorry.. but what size fuse? A ordinary spade fuse will be fine yeah? I only have a spade fuse holder..
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy Last edited by Falcon96XR6 on Tue Feb 25, 2014 9:53 pm, edited 1 time in total. |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
10amp would be fine the same as the original reverse lamp fuse in the fuse block? Wouldnt it?
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| MAD |
|
|||
|
Well, the fuse is there to protect the wire.
If you used the same size wire as factory, then yes, match the original. If not, use a fuse that matches the wire. |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
{USERNAME} wrote: Well, the fuse is there to protect the wire. If you used the same size wire as factory, then yes, match the original. If not, use a fuse that matches the wire. Alright thanks mate, as i said i dont know much about the electrical side of things ahah, Ive now done it all and hidden the wire so it cant be seen, and put a 10amp use. The lights work when put in reverse, so im happy for now till i can put it over the pit at dads work, just gotta remember as you said.. the reverse lights stay on even when ign off lol..
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| MAD |
|
|||
|
And keep trying to find the problem....
Like you said, it only happened after the conversion, it must be something simple. At least you know you've got the right R-BK wire on the switch. Just need to confirm you've got the right pink one and go from there. |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
{USERNAME} wrote: And keep trying to find the problem.... Like you said, it only happened after the conversion, it must be something simple. At least you know you've got the right R-BK wire on the switch. Just need to confirm you've got the right pink one and go from there. Yeah, it has to be the right pink one anyway, its the only wire left out of the 4 wire plug, im assuming the wire has just broken abit further up from when me and dad were soldering the resistors in, i just dont want to spend too much time under the XR with just a jack. You know? Safety and all. Lol 
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| MAD |
|
|||
|
Good idea. Jack stands are a must.
Or spare tyres under the wheels. |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
{USERNAME} wrote: Good idea. Jack stands are a must. Or spare tyres under the wheels. Thats a good idea.. old chaser rims would do the job yeah? I usually put a few blocks under the chassis if i only need to lift one corner, and just rest the weight evenly on the blocks and jack.
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
Got it all sorted, the wire had snapped right up the top of the loom under the bulk plug, now i have reverse lights as per factory and now my ABS and airbag lights on the cluster have turned off too
  so bonus. Cheers everyone for the help, and information, muchly appreciated! Kind regards, Tait.
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| Elfuturat54l |
|
||
|
My reverse lights are constantly on I bought the car like that it is manual converted any ideas what the go is there ?
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 8 guests |
