|
fezlane |
|
|||
Age: 58 Posts: 434 Joined: 18th Jul 2009 Ride: NL FAIRLANE BA TURBO POWERED Location: ballarat |
Hi Guys
I started to reinstall the dash on my Nl Fairlane today. When I was taking it out I thought I wrote down all the connectors but of course I have three mystery plugs. Here they are any help would be fantastic. {DESCRIPTION} first one {DESCRIPTION} second one {DESCRIPTION} Last one this one runs of the bit of loom that has the light under the glovebox whereas the oither two are higher up but still on left hand side of dash. Any help would be greatly appreciated. Thanks Steve |
|||
Top | |
snap0964 |
|
|||
|
1. Blend door motor - can't see all wires, so not 100%
2. Glovebox light ?? 3. Power antenna
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
Top | |
fezlane |
|
|||
Age: 58 Posts: 434 Joined: 18th Jul 2009 Ride: NL FAIRLANE BA TURBO POWERED Location: ballarat |
Thanks snap
You were right found power antenna wire Glovebox light cannot find light but according to wiring diagram this is it. Do you know where this light shouls\d be. The other plug I think is ATC servo assembly plug I think would this be auto temp control? Cheers Steve |
|||
Top | |
snap0964 |
|
|||
|
{USERNAME} wrote: Thanks snap You were right found power antenna wire Glovebox light cannot find light but according to wiring diagram this is it. Do you know where this light shouls\d be. The other plug I think is ATC servo assembly plug I think would this be auto temp control? Cheers Steve Well Steve, on the RHS of the recess where the glovebox lid goes into, the light and switch push in, but those two wires fit through the hole and plug into it first. Be careful, easy to short the power line and blow the CRT LP fuse. I think the other plug is the Blend door servo which sits on the top of the heaterbox - looks in your pic there is tape patch stuck there - maybe a non fairmont box has been put in, or hopefully, the blend door shaft hasn't been broken. Ray
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
Top | |
fezlane |
|
|||
Age: 58 Posts: 434 Joined: 18th Jul 2009 Ride: NL FAIRLANE BA TURBO POWERED Location: ballarat |
Hi Ray
Thanks for your help. It was the blend door servo. A bit of the sound deadening material had folded over and was covering the plug must have been like that from factory as it wants to stay that way. So a combination of failinhg light and my failing eyesight didn't help matters. Thanks again for your help. Steven |
|||
Top | |
snap0964 |
|
|||
|
No probs Buddy.
So every self test on the CC unit would come up with the favorite E2 fault code.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
Top | |
fezlane |
|
|||
Age: 58 Posts: 434 Joined: 18th Jul 2009 Ride: NL FAIRLANE BA TURBO POWERED Location: ballarat |
Once again thanks for the help. Now all i have to do is plug a few things in and hope I don't get any silly noises from BCM and everything works.
Steve |
|||
Top | |
snap0964 |
|
|||
|
Be wise to do a CC self test before putting the dash back up - the BDM might've been unplugged for a reason.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
Top | |
fezlane |
|
|||
Age: 58 Posts: 434 Joined: 18th Jul 2009 Ride: NL FAIRLANE BA TURBO POWERED Location: ballarat |
Will do.
Will I have to let the bcm reset as well? |
|||
Top | |
snap0964 |
|
|||
|
Nah. that should be okay.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
Top | |
fezlane |
|
|||
Age: 58 Posts: 434 Joined: 18th Jul 2009 Ride: NL FAIRLANE BA TURBO POWERED Location: ballarat |
All done.
Everything is working except ABS light is on will look at it over weekend didn't test climate control as I know it wont work as I am doing barra conversion and ecu will not be getting required signals. Will try and work that one out one day. Thanks for alll the help Steven |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 20 guests |