|
| Steady ED |
|
|||
|
Nah probably not, but because it's up high, it's got more 'leverage'
Not a huge amount, mind you, but enough to probably upset the front end of the E-Series a bit.
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| 80crm |
|
|||
|
Can some say "hello" to an aftermarket bonnet with a bulge for the EL's to allow the extra height of the BA motor. It will be better than cutting a hole the bonnet like JetXR...
Hmmm, but more importantly a APS phase 3 BA turbo in an EL might be fun. Mwahahahaha!!! |
|||
| Top | |
|||
| Steady ED |
|
|||
|
I'd be happy with an N/A motor, running an edit.
But yeah O-Kaaaay, if I HAVE to have the Phase 3 turbo motor...
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| fordzatmyplace |
|
||
|
Steady ED wrote: Nah probably not, but because it's up high, it's got more 'leverage'
Not a huge amount, mind you, but enough to probably upset the front end of the E-Series a bit. yeah I know what you mean, higher centre of gravity. Keep in mind, the old windsor was about 50+kg heavier then the I6. The windsor had cast iron heads opposed the six's alloy head. Much more heavy up top...
_________________ ^^^ What He Said
|
||
| Top | |
||
| mspw |
|
|||
|
Steady ED wrote: Nah probably not, but because it's up high, it's got more 'leverage'
Not a huge amount, mind you, but enough to probably upset the front end of the E-Series a bit. No....the leverage you're speaking of is relative to the mounting point only. Raise the mounting point and you'll achieve the physical properties your describing. Increasing the height of the deck and allowing for the proportional increase of its mas, any additional moments of torque are being taken up and absorbed by the engine mount rubbers proper. In real terms any felt affect would be marginal. The required bulge when substituted in a fibre bonnet replacement would surely offset any weight increase. Now of course if I'm wrong I'll cheerfully admit it....not bloody likely!
_________________
|
|||
| Top | |
|||
| Steady ED |
|
|||
|
You dont have to admit your wrong MSPW.
I would never force that admission from you using a very effective form of chinese water torture. 'Leverage' was kinda the wrong term. The heavier DOHC head is raising the center of gravity in the engine bay. It'll roll the whole front end around more basically. If I'm wrong, which is entirely possible, I'll gladly refuse to acknowledge it, and proceed to open up a new user account simply to avoid doing so. edit: Yeah agreed, the effectswould be minor, but it probably would effect front end response a bit. You're right about the bonnet, that would entirely offset the effect.
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| Nicko |
|
|||
|
the ba dohc standard engine weighs
225kg anyone weighed an ef engine?
_________________ Nicko |
|||
| Top | |
|||
| Demo_efman |
|
|||
|
Hey who cares what it will take to put a BA motor into an e series car!! Just think how cool it would be
 !! and im sure if you just put V8 suspension and stuff into it - it would do they job!! Or wouldnt it!! i dont really know just thought it would work better with a heavier motor!
|
|||
| Top | |
|||
| na2fairlane |
|
||
|
Demo_efman wrote: Hey who cares what it will take to put a BA motor into an e series car!! Just think how cool it would be
!! and im sure if you just put V8 suspension and stuff into it - it would do they job!! Or wouldnt it!! i dont really know just thought it would work better with a heavier motor!yeah right im sure ud spend 10 grand putting a ba motor into a e series eh? whats the point.. everything comes down to what you get for your money. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 35 guests |
