|
| fordriver1 |
|
|||
|
hi fellas
i need a map to install into my ms2 to get me going. can anyone supply their .msq file? i have a 6 cyl. cheers! scott
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| brock61 |
|
||
|
Have u set the constants in ur ms2 and what embedded code u running.
_________________ EA Brock Falcon
|
||
| Top | |
||
| fordriver1 |
|
|||
|
being that no one put their maps up i went ahead and did it the hard (and long) way. im using 2.88 embedded code. that is the latest one as far as im aware. i havent actually run the car as yet as my coil pack decided to pack up so no spark on ignition.
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| brock61 |
|
||
|
Unlucky!! does,t it s**t ya. Yeah 2.88 is the latest. I'm running 2.3, Theres not much difference just has a couple of more functions. Just a heads up, Before u start just check that the thermistor setting are right. To do this quickly just check what the intake temp is telling u, it should be close to ambient temp, if it reads like -7 there wrong. Only telling u cause it caught me out.
_________________ EA Brock Falcon
|
||
| Top | |
||
| fordriver1 |
|
|||
|
thanks for that. it it reading ok. now ive sorted out the spark issue (running off eecv) but it still wont start. obviously a fuel issue. the injectors are getting power on ignition, but there is voltage at the triggering wires going to each injector bank constantly. i would have thought there should only be a signal when it actually needs to squirt?
also what settings do you have in your 'priming pulse' section under startup/ ignition section? all my 'prime pw m sec' are set to '0' by default. cheers scott
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| brock61 |
|
||
|
my priming pulse is at 2.0ms. What are ur settings in Injector control.
_________________ EA Brock Falcon
|
||
| Top | |
||
| fordriver1 |
|
|||
|
injector open time (ms): 1.0
battery voltage correction (ms/v): 0.20 pwm current limit (%): 100 pwm time threshhold (ms) 25.4 injector pwm period (us) 66 are your cranking pulse widths 2 across the temperature range? im still unsure about the injector currents. the trigger wires have 12 volts or so ALL THE TIME. so what makes them squirt? im sure they are squirting tho as when i crank the motor i can smell fuel so i reckon it might even be flooding! im so close its frustrating! 
cheers
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| weeman |
|
||
|
The injectors always have +12v going to them with ignition on. The ECU grounds the injectors to fire them.
|
||
| Top | |
||
| fordriver1 |
|
|||
|
awesome. thanks weeman
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| weeman |
|
||
|
Also cranking PW of 2ms seems very low.
I'm running 10ms at -40 degrees to 3ms at 70 degrees. |
||
| Top | |
||
| fordriver1 |
|
|||
|
that also helps- keep em coming!
what car are you running the ms on weeman?
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| weeman |
|
||
|
ED XR6. I'm running a MS1 with MS-Extra firmware & have removed stock ECU.
|
||
| Top | |
||
| fordriver1 |
|
|||
|
dont suppose you would mind sending me your .msq file so i can compare my settings with yours?
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| fordriver1 |
|
|||
|
{USERNAME} wrote: Also cranking PW of 2ms seems very low.
I'm running 10ms at -40 degrees to 3ms at 70 degrees. do you mean 'priming pulse'? as 'cranking pulse' is set with % not ms.
_________________ there are three types of people in this world:
|
|||
| Top | |
|||
| weeman |
|
||||
|
Yeah priming pulse. Give me your email address and I'll send you my .msq file.
|
||||
| Top | |
||||
| Who is online |
|---|
Users browsing this forum: No registered users and 19 guests |
