|
| Slabz |
|
|||||
|
hey guys, if Jaysen's guide didn't work for you, give this one a shot. It worked for my EBII 6cyl so i'd say it will work with EA-ED falcons although EAs shouldn't need it anyway.
Feedback would be greatly appreciated so feel free to give it a read anyway.
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||||
| Top | |
|||||
| justfordima |
|
|||
|
Good guide, with nice pictures Slabz..
Just so you know, you don't have to run that wire.. Where the transmission plugs in with a square plug, you can connect the (from memory) the orange/black wire to the ground wire on the bottom (black), and it will achieve the same thing.. I had it done the first time like you described, but I thought it wasn't great, and I was cleaning up my wiring, so I found it easier to just bypass it at the plug. But your method still works, and it worked for me for a long time. Cheers
_________________ ;++JustForDimSim++;
|
|||
| Top | |
|||
| jessev1983 |
|
||
|
Good Doco mate. Its good to see one for Eb's
_________________ 97 EL Fairmont Ghia I6
|
||
| Top | |
||
| altedxr6 |
|
|||
|
yeah jaysens one was for the EF fans turning on and idle speed to the computer things the gearboxs is in "N"
But Jaysens doco did not have the inhibitor switch settings. |
|||
| Top | |
|||
| Slabz |
|
|||
|
thanks guys, i came up with this after i'd done the conversion and my car wouldn't start
 and because it worked fine and looked ok (IMO) i didn't need to refine it.
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| voxace |
|
|||
|
That's what the nuetral switch is for on the manual gearbox. Earths that relay (if you run the loom to it).
If you earth that relay permanantly like you have it just allows you start it in gear and stuff. |
|||
| Top | |
|||
| Slabz |
|
|||
|
voxace wrote: That's what the nuetral switch is for on the manual gearbox. Earths that relay (if you run the loom to it).
If you earth that relay permanantly like you have it just allows you start it in gear and stuff. yeah i know. my gregories manual also speaks of a clutch switch (which i dont have) so you can start the car when you have the clutch pressed in. That switch is also used to turning off cruise control i think (which i also dont have)
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| justfordima |
|
|||
|
I like starting in gear
 .. saves me pushing my car manually when the engine is manifold less, and so forth...
Cheers
_________________ ;++JustForDimSim++;
|
|||
| Top | |
|||
| Slabz |
|
|||
|
cars are HEAVY!!! i had to push mine about 500m and i was wasted afterwards
 although i am unfit as 
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 34 guests |
