|
| 19RIP |
|
||
|
^^ Thanks for the reply guys.
Looking at installing a BA airbox in an AU. Can I use the same bolt holes ?? Or does it require some modifying ?? |
||
| Top | |
||
| markr1967 |
|
|||
|
Mine..
  Has whacking great big 9" x 5" K&N Xtreme pod filter inside.
_________________ Hot Chilli Red EL XR6, 5-spd manual, with BF F6 TYPHOON motor and supporting mod's, 3" exhaust etc.. |
|||
| Top | |
|||
| Benno The Viking |
|
||
|
Can you buy the rubber sealing lip part for BA intakes separately? Mine was perished so I'd like to get a new one...if not, anyone want to buy a BA intake minus the rubber bit?
_________________ Build Thread |
||
| Top | |
||
| FAST-XR |
|
|||
|
{USERNAME} wrote: I'm pretty sure that all overhead cam 6 cylinder falcons run the same size from E to B not sure about F series. In regards to 'mouth' size anyway. E series run a 64mm TB. 3" silicone will fit over it B series run a 70mm TB. 3.5" silicone will fit over it
_________________ 07 BF MKII XR6T |
|||
| Top | |
|||
| bradfordau |
|
||
|
{USERNAME} wrote: so i cut my old slash shield i was going to throw out cos it was buggered. fitted it into the area behind the grill and screwed it in place, cut out to of front grill to let more air in and this is the result, noticed it right away and pod never got hot after driving for 30 mins around town    Seems like it would block the radiator a fair bit ? |
||
| Top | |
||
| huggiebear |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: so i cut my old slash shield i was going to throw out cos it was buggered. fitted it into the area behind the grill and screwed it in place, cut out to of front grill to let more air in and this is the result, noticed it right away and pod never got hot after driving for 30 mins around town Seems like it would block the radiator a fair bit ? EF EL and AU get all their air from the bottom vent dont they? im not 100% on AU's tho pod seems seriously oversized and pointless |
|||
| Top | |
|||
| 619GIE |
|
|||
|
this is how the lane is lookin now, just has a k & n panel filter with ba xr6t snorkel and piping
 
_________________
|
|||
| Top | |
|||
| head_ache |
|
||
|
This is how mine looks right now. Still looking into panel filters options though
|
||
| Top | |
||
| BongoKongo |
|
|||
|
I tried to keep my intake looking as standard as possible when looking at it from the top
I kept the top part of the original plastic intake & used fiberglass to make the rest of the plumbing fit around the supercharger & idler pullies. I Made it in sections that fit tightly & snugly together & are easily pulled apart to allow for me to change belts & pullies etc. Just before the main pipe connects to the air-box there is another intake that connects to the pipe-work which utilizes the gap between the left side of the radiator and the body. This setup sucks in a serious amount of cool air, but to the unedumacated viewer it just looks like the standard intake. It's hard to see but there is also a Homemade Typhoon extension at the front of the air-box that sucks air from under the left headlight. Cost: $15 bucks in materials & took about 3 hours to measure up & make. I have had heaps of request to make some more for others, but I'm afraid that I only intended to make two & the other one is on my xr6. This a rough sketch because you cannot see it properly in the photos:    
|
|||
| Top | |
|||
| ausedwagon |
|
|||
|
_________________ {DESCRIPTION} |
|||
| Top | |
|||
| thebeast. |
|
||
|
my set up for the moment
|
||
| Top | |
||
| yeehaw |
|
|||
|
Engine and intake......Black's a bit of a theme..
  Cheers |
|||
| Top | |
|||
| thebeast. |
|
||
|
really, i hadn't noticed.
looks good though |
||
| Top | |
||
| yeehaw |
|
|||
|
{USERNAME} wrote: really, i hadn't noticed. looks good though hehe.....Cheers..
|
|||
| Top | |
|||
| thebeast. |
|
||
|
good luck finding any oil leaks lol
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 7 guests |
