|
| falcon_hell |
|
||
|
Great post, very informative. Ive got a tickford head im thinking of puting on my ef but before doin that i was gunna get a cam and shave the head, any suggestions as to how much i should shave.
|
||
| Top | |
||
| phongus |
|
|||
|
heys. bit new at this but whats the difference between the Pacies PH4480 and the PH4499. I saw them on ebay but im not sure which one is better. the PH4499 is going for 330 while the other is going for 450. what are the advantages and disadvantages for both of them? cheers
phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| efbignik |
|
|||
|
hey voxace dude where did you get your
polished manifold from or did you do that your self??? i have got to get me one of them
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| voxace |
|
|||
|
efbignik: Take it to a metal polisher, check the yellow pages maybe. I did the rocker cover & thermostat housing myself, and that took bloody long enough.
phongus: PH4480's are the go, tuned length, smaller pipes for better torque. Much better design. falcon_hell: I would ask the head reconditioner for this advice. The head may have been skimmed or shaved before too, so keep that in mind. |
|||
| Top | |
|||
| phongus |
|
|||
|
thanks voxace
phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| efbignik |
|
|||
|
thanks voxace
how did you do your thermostat housing i mite give it a go
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| voxace |
|
|||
|
||||
| Top | |
|||
| efbignik |
|
|||
|
thanks Voxace
that was really handy and it's not that hard to do
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| a1drake |
|
|||
|
well after reading this very good tread i went down to the junk yard and got the el bbm manifold and all the bits including the ecu $ 350 ?, dyno man owes me a chip toque cpu chip $500 all i need is a cam ? $$$$?to suit ,should i use a vernier gear s and sprocket s$$$? two things i think i need ,all i have to do is put together !!do i use all the elec plugs on the manifold eb /el or are there spare ones ?
_________________ eb 4.0 falcon & f150 351 & caprice 5.0 |
|||
| Top | |
|||
| voxace |
|
|||
|
Mate I wouldn't really bother with the vernier gear, as most reground cams don't need it.
With the BBM, swap all of the wiring from you old manifold across to it, lengthening any of the wires as need. Then come time to install it, you will be able to plug it straight in and have it work right away. The manifold uses all of the same sensors, there won't be any spare. You will have to run one from the ECU, to the switch valve so that the manifold will operate correctly though. |
|||
| Top | |
|||
| HSVETAR |
|
|||
|
instead of the AUII XR8 snorkel, with a bit of modifying to the thermofan shrouding, you can fit a AU TE50 Snorkel, almost looks like a herrod motorsport one, its got the tickford wings in the moulding of it too. looks and works a treat.
_________________ EL 4.0, XR6 cam, Pacemaker extractors, 2.5" exhaust, 17" Advanti Racing Stalker Rims, Ultra Low King Springs, K&N Pannel filter, NOW MANUAL, 3.45:1 LSD
|
|||
| Top | |
|||
| Southy |
|
|||
|
any info on installing a Vernier Cam gear?
|
|||
| Top | |
|||
| EB V8 |
|
||
|
{USERNAME} wrote: Here's what the pacey's look like on Shugg's ITS motor:
 If I have an EL Ghia, tickford Motor. I change headers to Hurricane extractors and fit a high flow 2.5 inch cat but retain the standard exhaust, in addition I fit a Panel K&N filter and AUXR intake snorkel, what additional power what it make over the 162kw car??
_________________ EL Fairmont Ghia, extractors, 2.5 inch system, high flow cat, K&N panel filter, AUXR Snorkel, 3.45diff 0-100km/h 6.9secs
|
||
| Top | |
||
| Southy |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: Here's what the pacey's look like on Shugg's ITS motor: If I have an EL Ghia, tickford Motor. I change headers to Hurricane extractors and fit a high flow 2.5 inch cat but retain the standard exhaust, in addition I fit a Panel K&N filter and AUXR intake snorkel, what additional power what it make over the 162kw car?? if this is for an I6 no way. ud have to install a hot cam, full exhaust and all the rest of th goodies. |
|||
| Top | |
|||
| EB V8 |
|
||
|
Help me out.
What extra power would a set of Hurricane extractors with 2.5 inch high flow cat, retain standard exhaust, K&N Panel filter, AU XR intake snorkel. What are these mods going to ad over the standard 162kw
_________________ EL Fairmont Ghia, extractors, 2.5 inch system, high flow cat, K&N panel filter, AUXR Snorkel, 3.45diff 0-100km/h 6.9secs
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 39 guests |
