|
| smee |
|
|||
|
I'm doing this conversion right now.
what's the sensor under the timing cover - below the crank angle sensor on au ? |
|||
| Top | |
|||
| fastleno |
|
|||
|
{USERNAME} wrote: Hey 09RQR I recently did an AU1 into an EF falcon. Below is my response to what I did different: gezz it takes me 200 swear words just to change the oil filter.
ef thermo housing - I used the AU housing and simply added the sensor wire for the back of the head. ef aircon compressor and spacers - Spacers need to be cut down as the AU has large spacers on the block. I was not ablt to make the spacers at the time so I used some M12 nuts. 2 between the block and compressor and one on the other side. Used EF bolts as well. ef intake and harness - I onlu used the top half of manifold with EF harness. au plug and wire for the knock sensor - I simply unscrewed the AU sensor stud from the block and used the EF sensor that screws into the block. AU Fan Belt - I used the EF Belt. I did not swear much either. It just goes straight in. |
|||
| Top | |
|||
| Fiox |
|
||
|
Smee, I believe that sensor is the AU version of the crank sensor (like ef under manifold). Just leave it.
|
||
| Top | |
||
| SLY40L |
|
||
|
I'm thinking when my head goes, a Ba to EF! or is it seriously too much trouble?
|
||
| Top | |
||
| Eu-GenixX |
|
||
|
can anyone direct me to any info on BA motor into an AU?... in the mean time.. i will continue to search...
|
||
| Top | |
||
| newfella XG |
|
||
|
Gday guys
 hoping someone can answer my questions on this thread.
I have a xg ute that I need a replacement motor and auto for, and was wondering what motors I can drop straight in with little to no fuss? I am a bit confused with all the e series models. Also what sort of price for a motor and auto fitted, would I be looking at ? Cheers |
||
| Top | |
||
| xgdude |
|
||
|
{USERNAME} wrote: Gday guys
hoping someone can answer my questions on this thread. I have a xg ute that I need a replacement motor and auto for, and was wondering what motors I can drop straight in with little to no fuss? I am a bit confused with all the e series models. Also what sort of price for a motor and auto fitted, would I be looking at ? Cheers Just to add to this I am looking at fitting an AU motor into an XG but am a little confused as to if it is a straight fit or not?
_________________ EB 5.0lt 2.5" Exhaust Kings Super Lows blah blah |
||
| Top | |
||
| ferr007 |
|
|||
|
ok here is a tricky one i have a 68 xt falcon i am looking to put in an ef el motor in it now i know i need wiring etc but what will i need physically like mounts etc and does anyone know if it will fit ok also i was thinking of putting the single rail box thats in it back on to the later motor
what do you guys think |
|||
| Top | |
|||
| EFUTURA96 |
|
|||
|
hey guys just wonderin' about puttin' an au vct xr6 engine in my ef futura????? i realise the sump issues but not sure on any others that could arrise like ecu for the vct some one has told me that this is the biggest issue.
Dave
_________________ 96 EF FUTURA,16" FTR'S,2.5"REDBACK SPORTS EXHAUST,XR8 SPOILER,A/M SKIRTS BMC AIR FILTER,COLD AIR INDUCTION. |
|||
| Top | |
|||
| freedom::blue |
|
||
|
would there be much hassle involved if i wanted to put a BA engine & dash (ie. ecu & electronics) into my NC2 sportsman fairlane?
would the sump and bonnet be the only real issues? I was originally just really keen on having the BA interior in my lane, then I stumbled across this post.. |
||
| Top | |
||
| phongus |
|
|||
|
{USERNAME} wrote: would there be much hassle involved if i wanted to put a BA engine & dash (ie. ecu & electronics) into my NC2 sportsman fairlane?
would the sump and bonnet be the only real issues? I was originally just really keen on having the BA interior in my lane, then I stumbled across this post.. Will take a fair bit of cutting/moulding/re-shaping of the BA dash to make it fit in the NC2...trying to maneuver the dash in the car to cover all areas and also have functional heater/aircon and all that jazz will be tedious...unless you have heaps of money and time to throw at it. BA motor wise, shouldn't be hard to fit...some minor adjustments and it will go in. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| freedom::blue |
|
||
|
well i've got plenty of time, and a couple spare NA fairlanes that i guess i could use to reshape the dash into, then once it fits properly, put it straight into my NC, so i guess i should start going to auctions to find a totalled BA
|
||
| Top | |
||
| vards08 |
|
||
|
eyy people i need to change my cylinder head ( long story) nd i was wonderin if i can put a ef/el head on my eb falcon.. does anyone kno if itll work nd wat i would hav to change for it to work?
|
||
| Top | |
||
| Steady ED |
|
|||
|
Will go straight on.
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| fordless ford fan |
|
||
|
does the vct xr6 motor make it any harder any more problems
_________________ hi all how ya doing |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 30 guests |
