|
| Krytox |
|
|||
|
also, you undo/tighten them in sequence starting from the Middle working your way out. (refer to manual!)
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| stomper |
|
|||
|
Yeah like above...Go from the middle out when undoing the head bolts.
Get a breaker bar. Doesnt have to be long, just dont use the rechet. Slip a pipe over the end and pull like all f**k. Dont just ream the crap out of it but apply the pressure and it will crack. Once you do that it will come out easy as. Looks like your on the way to getting that head out. I used to pull the ford heads off and we had a breaker bar 1m long and that just had enough leaverage to do it. But use good heavy stuff like a breaker bar and an impact socket. We broke so many sockets undoing ford head bolts simply cause they were weak. Often that $15 set from supercheap will be better then the $150 set from sidchrome or snapon.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
| Top | |
|||
| Rick_Deckard |
|
|||
|
Hmmm, was reading the manual and it has the picture with the bolts number 1-14, seems I was confuzled by it though because I was going outside in with getting them out.
Anywho, thanks for setting me right, wish me luck.
_________________ E39 523i |
|||
| Top | |
|||
| Krytox |
|
|||
|
yes thats right.
Installing go up as in 1,2,3 etc (middle to outside) when removing go 14,13,12,11 etc (outside to inside) think about it, the head wants to LIFT so undoing the middle first will only make it harder to undo the last Outside bolts. so make sure you follow the manual with the procedure!
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| Krytox |
|
|||
|
i shoulda said that in the first place ... tightening sequence is always in to out.
loosen is opposite
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| Pulco |
|
||
|
do the reverse to the tightening sequence
_________________
|
||
| Top | |
||
| Rick_Deckard |
|
|||
|
s**t, dont' confuse me, lol. I was following the manual as you can see in the picture, I'm stuck on good ol' bolt 14, hehe.
K I got it now. : P
_________________ E39 523i |
|||
| Top | |
|||
| infusion69 |
|
||
|
dammit i dont know whether to get a mechanic to do my headgasket or do it myself
whats a avg price for a head gasket installed including head shaved etc? |
||
| Top | |
||
| Gaz |
|
||
|
800-1000 bucks id say.
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| Gaz |
|
||
|
oh, and probably a good idea to get that intake manifold and exhaust manifold off before you go undoing the head.
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| Pulco |
|
||
|
Gaz wrote: oh, and probably a good idea to get that intake manifold and exhaust manifold off before you go undoing the head.
hahah for sure...make it a lot easier!
_________________
|
||
| Top | |
||
| Rick_Deckard |
|
|||
|
Lol, I knew that, I think...
Exhaust is going to be a big problem, rusted bolts everywhere, lol. Will the cat be supported the weight of extrators? Worried about that.
_________________ E39 523i |
|||
| Top | |
|||
| Pulco |
|
||
|
yea it should be right while its sittin there...just make sure u bolt it back up
_________________
|
||
| Top | |
||
| Rick_Deckard |
|
|||
|
Lol, aye aye.
_________________ E39 523i |
|||
| Top | |
|||
| Pulco |
|
||
|
and stay out of the boot
_________________
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 74 guests |
