|
| xhi6ho |
|
||||||
|
hey guys i just finished making this air box adapter it replaces the standard plate and opens the hole up to 80mm. It is cnc machined 6061 ally. I would like to know if any of you would like to buy one? the price will be close to $80. If i get enough names i can make them, also the more names i get the cheaper i can sell them... let me know
|
||||||
| Top | |
||||||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
top idea mate, you could even have an angled lip on the inside so a pod filter bolts straight on
looks like your gonna sell a few of these 
|
||
| Top | |
||
| DARTHVADER |
|
|||
|
that is a rip snorter! Have you tried it on your FORD yet, if so what do u think?
_________________ AUIII, PACEY 4499's, MAGNIFLOW CAT, 2.5" ZORST, 17X8" AUII XR RIMS....otherwise all factory! |
|||
| Top | |
|||
| EFFII |
|
||
|
any chance you would make them longer?
I was thinking of puting a ba intake on my ef but with the ef box. from what i know the hose from the ba intake wont reach the box unless there is a longer adapter. |
||
| Top | |
||
| xhi6ho |
|
|||
|
the first lot i make will be the same size as this, i.e have already got that size material. but if i make them again i could definatly make a few changes, all your suggestions would be greatly appreciated. i have made 3 of these so far and they will be going on my xhxr6, an AU xr6 ute and an AU SR sedan. i will let you know the feedback and everything befor i start making them.
|
|||
| Top | |
|||
| WagonDad |
|
|||||||
|
Looks good. This is something I made up a while ago but the pipe goes into the box and uses the original rubber to connect either the original induction piping or an after market 3" pipe. Just a different approach, food for thought.
_________________ 4.0L EF Fairmont Station Wagon. EL GT Snorkel. K&N Pod in air box. 3" Intake piping.
|
|||||||
| Top | |
|||||||
| fordman351 |
|
|||
|
FaBz wrote: any chance you would make them longer?
I was thinking of puting a ba intake on my ef but with the ef box. from what i know the hose from the ba intake wont reach the box unless there is a longer adapter. Hey FaBz, i have the BA intake tube on my EL airbox, it will reach, it's just that it needs to be stretched slightly. The clamps that come with it hold it on the airbox very nicely. It cost me around $40 from memory. 
|
|||
| Top | |
|||
| Spoondog |
|
|||
|
must have to stretch it alot, i got a BA intake yesturday, and it gets no where near the EF airbox.
maybe cause u got a BA engine in urs its closer..
_________________ R33 GTS-T - 222.6rwkw |
|||
| Top | |
|||
| EFFII |
|
||
|
Spoondog wrote: must have to stretch it alot, i got a BA intake yesturday, and it gets no where near the EF airbox.
maybe cause u got a BA engine in urs its closer.. mate let me know if your able to get it to reach to the ef box. if you do well done!! Then i have to go out and find one for mine 
|
||
| Top | |
||
| EFFII |
|
||
|
fordman351 wrote: FaBz wrote: any chance you would make them longer? I was thinking of puting a ba intake on my ef but with the ef box. from what i know the hose from the ba intake wont reach the box unless there is a longer adapter. Hey FaBz, i have the BA intake tube on my EL airbox, it will reach, it's just that it needs to be stretched slightly. The clamps that come with it hold it on the airbox very nicely. It cost me around $40 from memory. Matt that looks awsome! i didnt even notice it was a BA engine until it was said. Send me one with the badges
|
||
| Top | |
||
| fordman351 |
|
|||
|
Spoondog wrote: must have to stretch it alot, i got a BA intake yesturday, and it gets no where near the EF airbox.
maybe cause u got a BA engine in urs its closer.. Ahh now i see what i have done haha. The intake pipe attached to the throttle on the DOHC engine is pointing more toward the airbox than the pipe on the EL SOHC engine. Soooooo, if you get a BA throttle pipe and flex pipe only then will it reach the airbox. |
|||
| Top | |
|||
| xhi6ho |
|
|||
|
WagonDad wrote: Looks good. This is something I made up a while ago but the pipe goes into the box and uses the original rubber to connect either the original induction piping or an after market 3" pipe. Just a different approach, food for thought.
did you cut the center out of the rubber? that is a pearler of an idea. is the k&n pod better than a k&n panel filter? |
|||
| Top | |
|||
| brad17djr |
|
|||
|
im interested lol can u still use the standard plumming from there to the t/b tho?
_________________ 2 FOR TURNING & 2 FOR BURNING |
|||
| Top | |
|||
| xhi6ho |
|
|||||
|
you could i guess. but the idea is to make everything bigger i just replaced my standard pipes with 3in stainless. you don't have to make any bends as you can use the standard elbows. its not ideal but untill i get my pacemakers and a proper mandrel bent intake, it will do.
|
|||||
| Top | |
|||||
| relaxed_diplomacy |
|
||
|
I make a rough guesstimate that if you rolled out that pod filter you would see its area to be similar to a panel filter. I only see hassles and cost in using a pod inside the box. Am i misssing something? Sound? Swirl?
_________________ wrecking 9/97 EL fairmont sedan burgundy 6cyl auto 270k modBAintake |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 142 guests |
