|
| Low_EFII |
|
|||||
|
I just went down to the wreckers to look for a single pipe air induction for my pod filter.
well i found exactly what i was after but they want $55 for it... (excluding airbox) anyone know where else to get these cheap? plastic or metal... cheers
|
|||||
| Top | |
|||||
| MoNGooSE |
|
|||
|
$55 is about what you pay for an EL air pipe like that... I payed $30 for mine but that was without the little piece of flexi-pipe to join the two solid sections. You can get crome, 3" mandrel bent pipes specially made up fir around the $100 mark at most exhaust places
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| Low_EFII |
|
|||
|
MoNGooSE wrote: $55 is about what you pay for an EL air pipe like that... I payed $30 for mine but that was without the little piece of flexi-pipe to join the two solid sections. You can get crome, 3" mandrel bent pipes specially made up fir around the $100 mark at most exhaust places
where did u purchase yours? |
|||
| Top | |
|||
| fordfreak ef |
|
|||
|
MoNGooSE wrote: $55 is about what you pay for an EL air pipe like that... I payed $30 for mine but that was without the little piece of flexi-pipe to join the two solid sections. You can get crome, 3" mandrel bent pipes specially made up fir around the $100 mark at most exhaust places still paid too much... my complete induction (rubber neck/ribbed rubber section and the two patic pipe bits sold for $20 on ebay ready to bolt on... 
|
|||
| Top | |
|||
| my el project |
|
|||
|
whils on the topic of intackes, i got offered a xr twin intack with the ticford badge on it fot $100 good or bad
_________________ El Futura
|
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
my el project wrote: whils on the topic of intackes, i got offered a xr twin intack with the ticford badge on it fot $100 good or bad
Holy s**t that's bad... Twin intake?! Do you mean just an EF intake with a Tickford badge?
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
Low_EFII wrote: where did u purchase yours?
I purchased mine off of a guy on these forums. It would be all good if I could find a goddamn piece of flexi-pipe to fit in between the two solid bits! But like Fordfreak said, I probably payed a tad too much... 
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| FAST-XR |
|
|||||
|
heres my setup
will cost you about 120ish for the stainless pipes and the silicone bend cheers
_________________ 07 BF MKII XR6T |
|||||
| Top | |
|||||
| Low_EFII |
|
|||
|
FAST-XR wrote: heres my setup
will cost you about 120ish for the stainless pipes and the silicone bend cheers damn tahts nice man do you notice a bit of a difference? my air intake on my EF is like a bbq hotplate over my engine 
|
|||
| Top | |
|||
| FAST-XR |
|
|||
|
thanks mate, yeah it does help as there are no more restrictions in diametre...
even if it only gives you an extra couple of kws, i would do it just for the look!
_________________ 07 BF MKII XR6T |
|||
| Top | |
|||
| fordfreak ef |
|
|||
|
FAST-XR wrote: thanks mate, yeah it does help as there are no more restrictions in diametre... yes..looks and performance wise you stand to gain a lot... and lose lil.. even if it only gives you an extra couple of kws, i would do it just for the look!  is definatly worth the trouble...-of which is not much... i also vouch for the 3 inch intake mod...
|
|||
| Top | |
|||
| sikford |
|
|||
|
FAST-XR wrote: heres my setup
will cost you about 120ish for the stainless pipes and the silicone bend cheers is it better to go stainless if doing that intake mod or can you go mild steel if ya want pipe that whole way round to the throttle body. cheers dan
_________________ THE Fairmont Ghia : 75th Anniversary LE |
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
You can get stainless all the way around... People simply use stainless because it looks nicer and lasts longer.
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| my el project |
|
|||
|
its the same as this one ($100) http://www.aus-ford-uk.co.uk/assets/ima ... bay_34.jpg[/url]
_________________ El Futura
|
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
Yeh mate... I've got one of those sitting right here which you can have for the cost of postage... They're worth s**t... You've got one under your bonnet as well if you care to look...
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 91 guests |
