|
| SlickNCGhia |
|
|||
|
Hi guys
my alternator wont hold in position when tensioning the alternator belt. the 13mm nut (u know what i mean) just spins when you turn it to the right. it never used to and im pretty sure ive tightened it properly since i had my AU motor put in. so at the moment i can only have the alternator belt so tight as the alternator just springs back after you tighten the belt with the 24mm bit. btw i have adjusted this a fair bit over the last couple of years due to my old motors crankshaft moving back and forth and snapping belts. any ideas people or anything i should check? as im going on a long holiday weekend and i dont really want any problems ie batt not starting. (i always keep spare belts) Thanks Heaps Ben ps sry bout the life story
_________________ NC Fairlane Ghia. AU engine. Pacemaker 4499. 2.5" Redback Zorst, tints, red dash. 17in ba xr (e-series). Suzuki Across (suzi) Sexy in Black |
|||
| Top | |
|||
| MadMatt |
|
|||
|
Sounds like the thread on the alt is stripped. You should be able to use a longer bolt and nut. I have not done this on a E series but it was a common fix on the X series.
_________________ Member Number 8804 |
|||
| Top | |
|||
| fastleno |
|
|||
|
if the 13mm nut just spins when you turn it to the right it sounds like the thread has stripped in the alternator, if so heres a quick fix, put a nut on the back of the 13mm bolt where it comes out the back of the alternator do it up semi tight then adjust the belt (24mm nut) then when you do up the 13mm bolt at the front hold a spaner on the back nut that you added
|
|||
| Top | |
|||
| SlickNCGhia |
|
|||
|
i dont think the nut it long enough to put a nut on at the back as i had a feel back there, so i guess i can just take the bolt out and put another one in thats long enough? are they a special size or thread pattern or anything?
cheers ben
_________________ NC Fairlane Ghia. AU engine. Pacemaker 4499. 2.5" Redback Zorst, tints, red dash. 17in ba xr (e-series). Suzuki Across (suzi) Sexy in Black |
|||
| Top | |
|||
| fastleno |
|
|||
|
SlickNCGhia wrote: i dont think the nut it long enough to put a nut on at the back as i had a feel back there, so i guess i can just take the bolt out and put another one in thats long enough? are they a special size or thread pattern or anything? yer use a longer bolt if need be and the nut just needs to be one that fits mate if its the wrong thread it wont screw on, you might find that the original bolt has no thread at the top where the head is to allow for the adjusting nut, but if you have a bolts and fastners joint near by take your old one in and thay will hook you up with the same thread and size and stuff with a nut to match in a high tensile for a few bucks.
cheers ben Last edited by fastleno on Fri Mar 09, 2007 12:03 pm, edited 1 time in total. |
|||
| Top | |
|||
| SlickNCGhia |
|
|||
|
yeah thanks i meant the thread for the bolt but iguess the tread in the alt is prob f**k so it prob wont make much of a diff. will raid bunnings tonight
thanks ben
_________________ NC Fairlane Ghia. AU engine. Pacemaker 4499. 2.5" Redback Zorst, tints, red dash. 17in ba xr (e-series). Suzuki Across (suzi) Sexy in Black |
|||
| Top | |
|||
| SlickNCGhia |
|
|||
|
ok so i had a play at lunch and it dosent look like a longer bolt will fit as there is a matal brace behind where the bolt goes through. (does anyone know if it will fit) also i took the bolt out and it looks like severall of the thread peaks have squared off so it may just be the bolt.
does anyone have any ideas of what to do? or of where i could find a replacement bolt after 6pm SE melb as im leaving early tommorrow. otherwise ill just chance it thanks ben
_________________ NC Fairlane Ghia. AU engine. Pacemaker 4499. 2.5" Redback Zorst, tints, red dash. 17in ba xr (e-series). Suzuki Across (suzi) Sexy in Black |
|||
| Top | |
|||
| SlickNCGhia |
|
|||
|
no-one knows if a longer bolt will fit? or of any other bodgy fixes?
is this gonna do any harm driving like this ie its not that loose thanks ben
_________________ NC Fairlane Ghia. AU engine. Pacemaker 4499. 2.5" Redback Zorst, tints, red dash. 17in ba xr (e-series). Suzuki Across (suzi) Sexy in Black |
|||
| Top | |
|||
| fastleno |
|
|||
|
arr weld it in place
|
|||
| Top | |
|||
| SlickNCGhia |
|
|||
|
lol - maybe some blue tac or liquid nails
_________________ NC Fairlane Ghia. AU engine. Pacemaker 4499. 2.5" Redback Zorst, tints, red dash. 17in ba xr (e-series). Suzuki Across (suzi) Sexy in Black |
|||
| Top | |
|||
| briney |
|
|||
|
pull the alty out and helicoil it.
_________________ vote for pedro ? f**k pedro, f**k him up his stupid a***hole. |
|||
| Top | |
|||
| [SXC3A] |
|
|||
|
i had the same problem, all i did was went to bunnings with the bolt found the the same size length and thickness and got a nut for it then did it up, works fine, and i did this about 5 months ago.
_________________ • F*** McDonalds... I'll make you go Mmmmmm...
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 72 guests |
