|
| Slabz |
|
|||
|
hey guys, i reckon i've chewed out shims on one of my HLAs (because i have an alted cam i needed them). My question (as above) is, do 3.9 shims fit into a 4.0 engine because i have a spare 3.9 i can flog them from which would make it all very convenient
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
depends what 4L it is. there are two type the change over was late in the EB2 production run, the diameters are 14mm and 11mm i think it is.
then you have 3 or 4 different hights in each ranging from 1.8 up to about 2.4 Last edited by tickford_6 on Mon May 15, 2006 8:03 pm, edited 2 times in total. |
||
| Top | |
||
| Southy |
|
|||
|
3.9 shims are 1.9mm and the bigger ones you can get are 2.4mm. Mine had 1.9mm in them but it rattled its tits off so i baught a set of 2.4mm and its like new now
|
|||
| Top | |
|||
| Slabz |
|
|||
|
i've got a July (pretty sure its July) 92 EB 4L... so they're all the same diameter but just different thicknesses?
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
they should be the 14mm ones you need. they might be a different thickness. they have the different one so that as things like a head reco are done you can remessure what the shim size should be an use the right one.
|
||
| Top | |
||
| Slabz |
|
|||
|
my problem is that i crunched up the washer type shims that you get with the RPD/alted cams (at least i think thats what i've done) so all i need is something to make up 1-2mm of shim-age (or whatever the ammount needed for a stg1 is - can anyone remember?)
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
1.8mm cheap from ford
|
||
| Top | |
||
| Slabz |
|
|||
|
tickford_6 wrote: 1.8mm cheap from ford
why not just use the ones from the 3.9?
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
Slabz wrote: tickford_6 wrote: 1.8mm cheap from ford why not just use the ones from the 3.9? the question was what size. the answer is 1.8mm if the 3.9 shims are not 1.8 then they are cheap to buy from ford................. |
||
| Top | |
||
| Slabz |
|
|||
|
tickford_6 wrote: Slabz wrote: tickford_6 wrote: 1.8mm cheap from ford why not just use the ones from the 3.9? the question was what size. the answer is 1.8mm if the 3.9 shims are not 1.8 then they are cheap to buy from ford................. gotcha
_________________ EBII 4.0L GLi | T5 | 3.27 Spool | POD | KKK K27 Turbo | 600x300x76 FMIC | 40mm Wastegate (dead) | RPD Stg1 Cam | B&M Launch Control | Thermos | 3" Dump | Twin 2.25" Zorst | 197kw@3500rpm, 7psi LEAN!
|
|||
| Top | |
|||
| Southy |
|
|||
|
the 1.8/1.9mm shims have 1 dot ingraved on the top so you can tell what they are without taking the lifter out. 2.4mm have 2 dots and 1.7 have no dots
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 80 guests |
