|
| Drapes54 |
|
||
|
Gday i am currently in the process of rebuilding an au short block to put into my ef xr6 im on a bit of a budget so wanting to use good secondhand parts and new parts where i can i am building this engine for boost and wanting to make huge streetable power out of it my ef xr6 has a dev4 kit so i am going to refresh the head and clean it up then put it on the au block once the au engine is finished
i managed to get a short block for cheap from the wreckers im wanting over 600rwhp at the wheels what sort of engine combo will be best suited to make this kinda of power? Can i use typhoon conrods and later model ford parts to keep costs down or would i be better off looking after market range all help and opinions are greatly appreciated cheers guy and gals |
||
| Top | |
||
| 66 coupe |
|
||
|
ok so you want 600+rwhp on a budget and good second hand parts...
ok mate no probs  and ensure your budget includes + transmission + engine management + diff |
||
| Top | |
||
| Drapes54 |
|
||
|
its got an au lsd diff in it that seems pretty tight and the g/box was rebuilt recently as well so both of those are pretty good its got a twin plate heavy duty clutch so that should support plenty of power i would of thought
|
||
| Top | |
||
| 66 coupe |
|
||
|
if you want 600rwhp budget around 20k
|
||
| Top | |
||
| phongus |
|
|||
|
It will definitely won't be a cheap project.
Even if the gearbox has been rebuilt, has it had any upgrades to be able to handle 600rwhp? Diff might be tight, for the current power you have, but might not be strong enough. Add to that, you will need a stronger tail shaft over the stock. You said streetable, I would not consider 600rwhp a streetable car, especially on a car without adequate braking or traction control, you'd lose the back end quiet readily, but that's just my opinion. When you say you are in a bit of a budget...what dollar figures are you talking about here?
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Drapes54 |
|
||
|
i dont have figures as such but i know that i would like to use new parts where i can but stick to good second hand parts when i say streetable i should really say registered lol i found a bottem end rebuild kit brand new forged internals for $2090 bucks with spoolimports rated at 1000 horsepower but it will take me a while to save that up curious of i could put ba -fg f6 typhoon or xr6 turbo conrods in it?? would they be capable of huge power? and what sort of pistons would be recommended to run in it along with oil pump and all the other stuff required?
|
||
| Top | |
||
| Drapes54 |
|
||
|
oh and what sort of turbo would be recommended my one that i have is rated at 400hp im wanting one rated at 1000hp
|
||
| Top | |
||
| phongus |
|
|||
|
Drapes54 wrote: i dont have figures as such but i know that i would like to use new parts where i can but stick to good second hand parts when i say streetable i should really say registered lol i found a bottem end rebuild kit brand new forged internals for $2090 bucks with spoolimports rated at 1000 horsepower but it will take me a while to save that up curious of i could put ba -fg f6 typhoon or xr6 turbo conrods in it?? would they be capable of huge power? and what sort of pistons would be recommended to run in it along with oil pump and all the other stuff required? If it's going to take you a while to save up for the bottom end, it will be a long time before you can get everything for a complete motor with turbo, cooling, intake etc. I'm not sure with the conrods, however I have heard even the dedicated LPG motors had some XR internals, not sure if it was conrods/pistons or the whole assembly though. Power wise, I can't see stock internals reaching your goal of 1000hp maybe 500hp...reliability would be compromised. Can't help on the turbo.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Drapes54 |
|
||
|
im aiming for around 600hp if possible
|
||
| Top | |
||
| 66 coupe |
|
||
|
start writing your list:
custom CP pistons Scat Rods main and head studs cam, valve springs, valves, retainers, collets head work machining dummy assembling deck the block final assembly injectors engine manangement system fuel system transmission controller turbo + plumbing + intercooler, boost control can be done via ecu, wastegate like i said above be prepared for 20+ for your 600+ hp at the end of the day unless you plan on just using stock internals and settling for around 300-400hp - I built the motor in my TT EL with std pistons, egas rods etc and that went consistent 12.2 at 114mph with stock trans, stock converter, 3.08 diff ratio, aftermarket management and e85. check out shiftkits.com.au/gallery but to step up from here there is more cost involved - trans needs to be upgraded possibly t400 or c4, diff, axles etc you cant just go throw a 600+ hp motor in and expect everything behind it to hold up. |
||
| Top | |
||
| Drapes54 |
|
||
|
ok so considering my car is a manual with an au 3:45:1 lsd diff in it what sort of power would be more suitable to aim for id like somewhere in the 500+ horsepower range what sort of clutch would be ideal for this set up would i need to change my diff to something stronger? what size turbo would be ideal for that sort of power as well mines rated at 400 but wanting more then 500 so whats gonna be the way to go in that side of things?
cheers guys |
||
| Top | |
||
| Drapes54 |
|
||
|
it also has a worked head in it so i dont need to do anything to the head just make sure its still in good condition
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 83 guests |
