|
| KyleBardell |
|
|||
|
basically the above, can I put an AU3 head on an ED Sump?
Cheers Kyle
_________________ The Luxo Cruiser - 07 BF Fairlane |
|||
| Top | |
|||
| Johnson stroker |
|
|||
|
I assume you mean put an AU head on an ED block? yeah straight swap over, you gonna run the au cam and rocker gear as well I assume? otherwise if you want to run an e series cam you will also need e series rocker gear to retain the correct ratio, but if its the complete au head ie head cam and rocker gear, then yes straight bolt on.
_________________
|
|||
| Top | |
|||
| Disco Frank |
|
|||
|
KyleBardell wrote: basically the above, can I put an AU3 head on an ED Sump?
Cheers Kyle NO you can not
_________________ RIP SCOTT |
|||
| Top | |
|||
| Disco Frank |
|
|||
|
dc_todd wrote: I assume you mean put an AU head on an ED block? yeah straight swap over, you gonna run the au cam and rocker gear as well I assume? otherwise if you want to run an e series cam you will also need e series rocker gear to retain the correct ratio, but if its the complete au head ie head cam and rocker gear, then yes straight bolt on.
but i am pressuming this is what you are after and i agree with DC_todd
_________________ RIP SCOTT |
|||
| Top | |
|||
| KyleBardell |
|
|||
|
this part circled
 
_________________ The Luxo Cruiser - 07 BF Fairlane |
|||
| Top | |
|||
| phongus |
|
|||
|
The AU head will fit on the ED BLOCK if it's a complete head as dc_todd mentioned...
BUT, AU head will not fit ED SUMP as you stated in the thread heading... I am sure you meant BLOCK right? phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| KyleBardell |
|
|||
|
phongus wrote: The AU head will fit on the ED BLOCK if it's a complete head as dc_todd mentioned...
BUT, AU head will not fit ED SUMP as you stated in the thread heading... I am sure you meant BLOCK right? phong =P~ The Rocker cover and the bit the rocker cover goes on (Head), that is all.
_________________ The Luxo Cruiser - 07 BF Fairlane |
|||
| Top | |
|||
| gogetta |
|
|||
|
yes they are just being pedantic...
your complete head assembly will bolt to the block...although im not sure what u compression ratio will end up being (i think it migh be a bit lower - ie not as good)
_________________ |
|||
| Top | |
|||
| Grimketel |
|
|||
|
damn they all beat me to it..
as long as you have the block in between then yes the head will be quasi conected to the sump...
_________________ enough isn't enough |
|||
| Top | |
|||
| MAD |
|
|||
|
KyleBardell wrote: The Rocker cover and the bit the rocker cover goes on (Head), that is all. So the actual question is will an ED rocker cover fit onto an AU head? not AU head onto ED sump? |
|||
| Top | |
|||
| KyleBardell |
|
|||
|
MADXF wrote: KyleBardell wrote: The Rocker cover and the bit the rocker cover goes on (Head), that is all. So the actual question is will an ED rocker cover fit onto an AU head? not AU head onto ED sump? nah, there the 2 bits i want to change, rocker cover and head.
_________________ The Luxo Cruiser - 07 BF Fairlane |
|||
| Top | |
|||
| MAD |
|
|||
|
Ahh, in that case the answer is as above. A complete AU head will fit onto the ED block.
|
|||
| Top | |
|||
| turbotrana |
|
||
|
AU head fits ED block but I would be carefull as to what gasket you use.i.e the standard gasket or the AU metal gasket.
You have to check the piston to head clearance as by my calculations you will get anywhere from 20 to 30 thou clearance using the AU gasket. 30 thou may be OK but 20 wont. Alot of guys have used the AU gasket and I am yet to see/hear a problem of piston contact tho, but by my calcs its really really close. The AU gasket is 25thou. Most engine buiders aim for around 35thou clearance.
_________________ Turbo 6s rule |
||
| Top | |
||
| KyleBardell |
|
|||
|
i would be getting the AU Gasket
_________________ The Luxo Cruiser - 07 BF Fairlane |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 62 guests |
