Okay guys, so I'm thinking about putting a series 3 AU tickford motor in my 1998 XH
Motor has 80,000kms on it and it has a DEV 5 jim mock cam in it. I've seen a few of the posts on the swap but just wanted to be sure.
Would some one be able to tell me what I need to do to fit it and what the best way to set it up would be (intake manifold, fuel set up etc..)

Install for the XH will be as for the EL.

If yours is not an XR is still should still have the old style Log Manifold. You can refit that to the AU Motor or you can install a BBM. If going with the BBM you will need one from an EF/EL or at least the upper half and the throttle body, you will also need to change the throttle cable as well.

Things required to fit AU engine to EF/EL (updated 15/02/14)

1) Sump needs to be modified to fit K-Frame, you can cut and weld the K-Frame but that is up to you, will need engineering after being cut. You cannot use an E Series sump as the sump is totally different to AU. There are cases of the E series sump being used but filler plates or large quantities of sealant were used, not recommended. Also you loose the advantage of the cross bolting of the AU sump when using the E series sump, one of the major strength points of using the AU Block.

2) You need to use AU/BF alternator or you will need to modify the block and drill and tap mount points to mount the EF/EL alternator.
If you use an AU I alternator you will need to change the plug for the alternator to one from an AUI as these are different from the Mitsubishi alternators.
Note: The AUII & III and BA alternators have the same plug as EF/EL.

3) Remove the Oil Drive Block where the Dizzy (EL) or cam sensor (EF) goes and remove the gear from the shaft and fit to your Dizzy (EL) or Cam Sensor (EF). This will then mean that the gears are matching and you should have no issue’s, there have been issues with dizzy’s failing when this has not been done. Some modding will be required to use the existing mount point, extra notch in the clamp plate or grind the tab off the Cam sensor.
Note:Do not try and drill hole in existing EF position on AU block, you will drill through the block.

4) You will need to use an EF/EL thermostat housing as these have your temp sensor and AU housings do not. You could use the EB type if you wish as this has an extra fitting for an additional sensor is required at a later date.

5) You will need to use the EF/EL BBM as the upper section is different to the AU. Also use the EF/EL throttle body as some of the plugs are different to the AU.

6) Use the EF/EL wiring loom.

7) You will need to tap the block on an AUII/III Block with an M12 1.5 tap if using the EF/EL Knock sensor. AUI is already tapped with the correct thread for the EF/EL Knock Sensor. If using the AU sensor you will need to modify the plug.

8) a) You will need to cut the EF/EL AC pump mount spacers down to 30mm to suit the AU block as well as shortening the bolts by 10mmm if using the AU alternator to suit the standard serpentine belt.
b) If using the EF/EL alternator with modified mounts you will not need to cut down the mounts and be able to use the standard Serpentine belt.
c) Alternatively you can use the AU alternator , standard AC spacers and a Serpentine belt from an XH (Slightly longer).

9) Use the EF/EL power steering pump. This is a direct bolt up. The AU pump hose connection is different to the EF/EL.

10) You do not need to change the Harmonic balancer for either EL (Dizzy) or EF Coil Pack.

11) If fitting to EF you will need to use your original Coil Pack or an AUI coil pack as these are different to AUII & III. (different plug) You can use an AUII/III coil but the plug with need to be changed as well as different leads.

12) You can use the AU head or fit you EF/EL head, that is up to you.

Thank you so much for that I appreciate it!