|
| grizley |
|
||
|
hi all. just wondering how the au 6 would cope with a turbo. and how hard it is to get decent power out of them, would you be able to bet the same sort of power as a ba turbo or would it be to highly strung.
cheers Graeme |
||
| Top | |
||
| Joesau |
|
||
|
bearing in mind your motor is healthy, you'll push 200rwkw with a breeze. ranging from 6-8 psi. some ba turbo's punch out up to 220rwkw ive seen on a dyno each car is different, seen a ba turbo pull 182rwkw at the same joint same day so you cant really go by that figure. It pretty easy to get good power from it, especially if you rebuild it and decomp to run more boost, PENDING HOW SERIOUS YOU WANT IT TO GO????
|
||
| Top | |
||
| grizley |
|
||
|
well it would have to be rebuilt. this is for a project im yet to start. it would be going into an ea and i know the au is alot easlier to make fit then the ba.
|
||
| Top | |
||
| madeaspack |
|
||
|
im running a stock 70,000km au motor with a snort stage 3 kit running 9 psi,not sure on power as yet but it goes pretty hard,have got a very good tune,am going to run 15psi with the stock motor as soon as i upgrade the clutch,its just holding on
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| ebxr82nv |
|
||
|
madeaspack wrote: im running a stock 70,000km au motor with a snort stage 3 kit running 9 psi,not sure on power as yet but it goes pretty hard,have got a very good tune,am going to run 15psi with the stock motor as soon as i upgrade the clutch,its just holding on
15 psi on a stock bottom end, best of luck with that, maybe you shouldnt get your ambitions mixed up with your engines capabilitys. looking into my crystal ball I see bent rods and smashed pistons in your future. And to grizly if you havent bought the motor yet look for an lpg bottom end and put it with a petrol top end the lpg bottoms are much stronger
_________________ 9/98 AU1 XR6hp-about to retire from the road and be reborn on the race track. |
||
| Top | |
||
| Joesau |
|
||
|
haha 15 psi wake up to ya self!! i can see a rod hanging out the side of the sump already! now seroiusly your not serious hey? cos its pretty dumb thinking that a standard motor will the hold the 15 pound! and whoever told you it would be fine is just as dumb and doesnt know nothing
|
||
| Top | |
||
| GeZza200 |
|
||
|
iv been told the bottom ends are good for around 300kw and 15psi would be quite a bit over that id say.
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||
| Top | |
||
| Bundy Rum |
|
||
|
in theory, how would a stock auto AU monty ghia hold up with a 9psi supercharger on it?
_________________ www.myspace.com/beefcakebrent www.aufalcon.com/bundyrum
|
||
| Top | |
||
| Grimketel |
|
|||
|
Bundy Rum wrote: in theory, how would a stock auto AU monty ghia hold up with a 9psi supercharger on it?
fantastically as long as it is well maintained. 9-10 psi is the upper safe operating limit on the engine. you can go a couple higher but misuse and hard k's will push it over the limit. 9 is a good mark to aim for for power and reliability. auto's are stronger than the manuals to funnily enough.
_________________ enough isn't enough |
|||
| Top | |
|||
| madeaspack |
|
||
|
with a good tune 15psi will be fine,you just wait and see,if she lets go i'll eat my words,but hey motors are cheap anyway
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| Bundy Rum |
|
||
|
thanks for the advice guys. ill stick with 9psi and a dyno just to make sure it works sweet... want bit more performance but i dont really want to change the car too drastically. got my zorst comin in 2 weeks. after that its wheels the supercharger!
_________________ www.myspace.com/beefcakebrent www.aufalcon.com/bundyrum
|
||
| Top | |
||
| Joesau |
|
||
|
a factory bottom end wont hold 15 pound, if you take it to any decent tuner im sure they will tell you this.
|
||
| Top | |
||
| Johnson stroker |
|
|||
|
no no.. don't listen to them.. Your motor was made to have 15 pounds shoved into it. It will take 15 pound. Once.
_________________
|
|||
| Top | |
|||
| GeZza200 |
|
||
|
lol, they wernt even designed for turbos let alone shoving 15psi through it lol. It wont last very long at all at 15psi
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||
| Top | |
||
| madeaspack |
|
||
|
it'll take 15 psi,tuners will tell you it wont because they dont want it to be on them if it blows,they'll cover their a** and not tune it at 15.im confident it will last at 15psi and so are a few guys i know have been doing turbo stuff to falcons for years
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 41 guests |
