|
| camcam |
|
||
|
OK so I have got a well done up au 3 motor in my ef used the ef sump and oil pump and chain cover to make it fit. Ef loom au 3 alternator and au belt all fit fine runs and is lumpy as f*** sounds sick. But now this were i need help it running so rich and fuel pump can't really handle it any reason why it's so rich and how could I fix it? The mods fone are forged pistons rods acl berings belanced crank valves ported and stock car cam any idea any think will half thanks
|
||
| Top | |
||
| Mad2 |
|
|||
|
{USERNAME} wrote: OK so I have got a well done up au 3 motor in my ef used the ef sump and oil pump and chain cover to make it fit. an AU motor's sump is differant to a EF .... so did you have much trouble moddin it?? |
|||
| Top | |
|||
| camcam |
|
||
|
No used ef timing cover and oil drive lines up mean
|
||
| Top | |
||
| SWC |
|
||
|
Timing cover for the EF and AU are the same where the sump bolts up.
Difference with the AU Engine is the rear main cap which has a smaller outer dimension which means that there is a gap between the cap and the EF/EL sump where the gasket goes. Also you can't use the crossbolts from the AU when using the EF/EL Sump therefore loosing some of the bottom end strength. |
||
| Top | |
||
| Falcon96XR6 |
|
|||
|
You had the sump off already...
You should've just got it modded for $100 bucks like I did and be done with it... Least you don't loose any strength.. That's one of the main factors of going an AU donk.. I was under the impression the EL sump wouldn't go on at all.. But apparently you've done it so it's possible.. I just don't see why.. Lol
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| camcam |
|
||
|
Yes it fits no gap is fine that's not wat I need to no I need to no wat I can do to stop it running rich
|
||
| Top | |
||
| Falcon96XR6 |
|
|||
|
Check O2 sensor and fuel pressure regulator. - to start with.
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| camcam |
|
||
|
Sweet thank you bro will got on to in now
|
||
| Top | |
||
| Falcon96XR6 |
|
|||
|
If O2 sensor is over 100k km old - throw it away, and replace it with a new one,
And the fuel pressure reg - suck on the vacuum hose on top of it, if you taste/smell petrol the diaphram inside is ruptured - new reg required
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
Also, check the vac line going to the MAP sensor on the firewall, common to crack and will cause car to run rich and like a dog.
Otherwise, coolant temp sensor, air intake temp sensor, map sensor itself,
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| SWC |
|
||
|
{USERNAME} wrote: Yes it fits no gap is fine that's not wat I need to no I need to no wat I can do to stop it running rich If there is no gap between the rear main cap and the sump, then it's not an AU motor. Do the Main caps have cross bolts? |
||
| Top | |
||
| camcam |
|
||
|
Oi yes it is a au 3 I work on the motors 4 years in stock cars and it is a ef sump you use the ef oil drive and ef timing cover it fits that's not wat I was asking tho. And ya the map sensor was the problem thank for the help man
I'll take pic later to prove it |
||
| Top | |
||
| SWC |
|
||
|
Mate, I have been doing these conversions for years. There is a significant gap at the rear main if using the EF/EL sump un an AU bottom end.
The only way to overcome this is to use the rear main cap from an EL Hybrid and have it line bored to match the rest of the mains or use a filler plate (or has been done in the past by others, fill the gap with silicon). The EF oil drive as you call it is actually the Cam Sensor which also drives the oil pump as does the dizzy in EA-ED and EL. You don't need to use the EF timing case as the AU one is fine. Shoot us the pics of the bottom end and sump and we can check it out. |
||
| Top | |
||
| camcam |
|
||
|
It's gasket gooed up. But it not wat I asked I need to stop over fueling
|
||
| Top | |
||
| SWC |
|
||
|
{USERNAME} wrote: It's gasket gooed up. But it not wat I asked I need to stop over fueling Check your o2 sensor, and also check vac hoses to your MAP sensor, or even the MAP sensor itself. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 42 guests |
