|
| shai12 |
|
|||
|
Hi, just got meself a wrecked Au just wondering whats involved in swapping the running gear out of the Au into my El Fairmont .
they both sixes with auto's |
|||
| Top | |
|||
| voxace |
|
|||
|
You need to modify the crossmember so that there is enough clearance for the sump, and also get the dizzy running in the AU motor so that it will work with your ECU.
I don't think there will be any issues with the gearbox, but a bit of fiddlign around with the motor. |
|||
| Top | |
|||
| twase |
|
|||
|
shai12 wrote: Hi, just got meself a wrecked Au just wondering whats involved in swapping the running gear out of the Au into my El Fairmont . Finally worked out the quote button they both sixes with auto's 
As far as the motor change goes I have documented my motor change here , it refers to an EF but most would be applicable to you. http://users.tpg.com.au/wasons/efau.doc I am still working on the knock sensor though, it pings a little on Petrol but OK on LPG, I think the AU sensor characteristics are different from the EF one. The only other difference is the EL's distributor, that shouldn't be to much of a drama though. Also there is a thread or two on the subject that has been posted here in recent times. Cheers TW.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| shai12 |
|
|||
|
Ok Thanks for that guys I think I can handle the conversion so I shouldnt have any probs with the Au tranny it should line up with the mounts am I correct there , the only thing I'm concerned is the dizzy how do I get it to work with the Au motor
|
|||
| Top | |
|||
| twase |
|
|||
|
shai12 wrote: Ok Thanks for that guys I think I can handle the conversion so I shouldnt have any probs with the Au tranny it should line up with the mounts am I correct there , the only thing I'm concerned is the dizzy how do I get it to work with the Au motor
The dissy should not be a problem, the AU motor has a dummy shaft to drive the oil pump, it should be a simple job to remove this and replace it with the EL distributor (timing aside), one thing that might complicate this is the clamp position has changed from EF/EL to AU from back to the front (at least the one I did) Cheers Tw.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| shai12 |
|
|||
|
Ok also would it be possible to use the Au ecu and wiring loom
|
|||
| Top | |
|||
| twase |
|
|||
|
shai12 wrote: Ok also would it be possible to use the Au ecu and wiring loom
Possible maybe, it would give you Sequential injection and allow you to retain the coil pack and other AU motor sensors but I would think you would run into Cluster / Smartlock and other issues which may make this not an attractive proposition. I don't have any experience here, others may be able to give you more accurate advise on this. Cheers TW.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| Disco Frank |
|
|||
|
shai12 wrote: Ok also would it be possible to use the Au ecu and wiring loom you could but would require alot of work for little benifit if you had a ef then it would be a matter of replacign the ecu and the engine and thats all.
sine you have EL you will have to chop/change the AU loom to get it all to work... then u could use the coil pack.: ) best bet would be to put the AU engine into the EL with a dizzy
_________________ RIP SCOTT |
|||
| Top | |
|||
| twase |
|
|||
|
I have revised my documentation, if you are referring to it on your conversion then you need the EF knock sensor.
http://users.tpg.com.au/wasons/efau.doc
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| shai12 |
|
|||
|
Ok thanks for the info ,the El knock sensor wont work or will it
|
|||
| Top | |
|||
| twase |
|
|||
|
EF and EL would be the same unit I would think.
Cheers
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| shai12 |
|
|||
|
Just been informed from another forum site that the Au tranny wont fit the El as it is longer can anyone verify this for me as I wanted to use the Au tranny in the conversion aswell
|
|||
| Top | |
|||
| xr8 dismantler |
|
|||
|
thats a load of crap.
best stick to the best ford forum site 
the el and au trans will interchange i have sold plenty of EL transmissions to go into AU taxis |
|||
| Top | |
|||
| twase |
|
|||
|
Beat me to it Darren, I was about to recommend he talk to you.
Cheers TW.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| xr8 dismantler |
|
|||
|
twason wrote: Beat me to it Darren, I was about to recommend he talk to you.
Cheers TW. hows your conversion now? do you think it was worth the extra stuffing around? honest opinion
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 50 guests |
