|
| Mr220kw |
|
|||
|
Just wondering what people use to remove the seal/bush behind the idler pulley near the power steering pump on an Au VCT?? Got a leak and I want to fix it asap.
Cheers Mr220kw |
|||
| Top | |
|||
| johnsblackbaxts |
|
|||
|
Hope this bumps the question/topic up the list. I have the same issue right now and am hoping someone can shed some light on the replacement procedure.
Cheers guys
_________________ Disclaimer: The above is the author's personal opinion and is not the opinion or policy of his employer or of the little green men that have been following him all day. |
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
Are you sure it the idler bush as there is no oil in the bush, more likely the timing chain tensioner seal is leaking
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| TROYMAN |
|
||
|
there is no seal...
its just leaking between the gasket and bolt hole.. just re fit the bolt with silicon on the shaft... |
||
| Top | |
||
| EDXR6-Poly |
|
|||
|
TROYMAN wrote: there is no seal... its just leaking between the gasket and bolt hole.. just re fit the bolt with silicon on the shaft... Seal/o-ring I have a tapered O-ring in mine lol bit of rubber grease on it when i reinstalled it and havent had a problem since
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| TROYMAN |
|
||
|
EDXR6-Poly wrote: TROYMAN wrote: there is no seal... its just leaking between the gasket and bolt hole.. just re fit the bolt with silicon on the shaft... Seal/o-ring I have a tapered O-ring in mine lol bit of rubber grease on it when i reinstalled it and havent had a problem since well there is no seal on mine.. there never was.. but it did seep a bit of oil after the bolt was removed so i just used gasket silicon... |
||
| Top | |
||
| Mr220kw |
|
|||
|
Just to clarify. It's actually not the bush but the mount the idler sits on. I think there might be some kind of seal in this mount. The mount itself presses into the timing chain cover. I've tried cleaning the bolt and resealing it as advised on this or another forum. Fixed the problem for a while then started leaking again.
Cheers Mr220kw |
|||
| Top | |
|||
| TROYMAN |
|
||
|
the idler mounts to the powersteering pump bracket which is bolted through the timing case..
are we talking about the same thing??? |
||
| Top | |
||
| Mr220kw |
|
|||
|
Yes that's the one
Mr220kw |
|||
| Top | |
|||
| Mr220kw |
|
|||||||
|
Okay,
I had another go at fixing the leak. Removed bolt and pulley. Cleaned bolt and hole. Added three O rings to plain section of bolt. Applied some Black Maxx sealant and reinstalled. Hopefully this will fix oil leak. Now I've just got to get the power steering rack fixed, which I found leaking.  Some photos included. Camera phone. Cheers Mr220kw
|
|||||||
| Top | |
|||||||
| EDXR6-Poly |
|
|||
|
pretty sure when I replaced my gaskets in my VCT motor where that bolt goes the gasket should seal that bolt you shouldnt need O-Rings and sealant but keen to see if that fixes it maybe try a copper washer too to help seal it
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| Mr220kw |
|
|||
|
G'day
I have finally fixed this. All i needed to do was to seal the thread on the bolt. It's amzing how such a little leak can cause such a friggin mess. Don't bother with the attempt in the pictures above it does SFA. Ah the joys of owning cars  Mr220kw |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 91 guests |
