|
| moody |
|
||
|
why bother putting a new bell mouth on it? wouldnt it be just as good if not better to just cut the whole thing off at the neck? tahts what ive done to mine and its done something.
|
||
| Top | |
||
| rushed |
|
|||
|
the bellmouth is so it picks up air at the (near) center of the panel filter, not just the back corner.
|
|||
| Top | |
|||
| GeZza200 |
|
||
|
The EL intake box doesn't have a bellmouth at all though
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||
| Top | |
||
| EL__Fairmont |
|
|||
|
moody wrote: why bother putting a new bell mouth on it? wouldnt it be just as good if not better to just cut the whole thing off at the neck? tahts what ive done to mine and its done something.
Have tried that, but throttle response isn't as good and you notice a small delay when accelerating the car from slow to high speeds. like a hesitation you get sometimes with pod filters.
_________________ 97 EL Fairmont 4l OHC .Silver. Last edited by EL__Fairmont on Thu Apr 12, 2007 11:37 am, edited 1 time in total. |
|||
| Top | |
|||
| EL__Fairmont |
|
|||
|
GeZza200 wrote: The EL intake box doesn't have a bellmouth at all though
yeah it does. if you look closly it has a rubber bellmoth integrated into the 4 bolt airbox adaptor.
_________________ 97 EL Fairmont 4l OHC .Silver. |
|||
| Top | |
|||
| FAST-XR |
|
|||
|
yeah the el box does have one at that adaptor, i would piss it off, it just resticts it!
why would having an exit of 52mm at the back of the box opening up to 75mm in the pipe furthur up be worthwhile? also, how is picking up air from only the front half of the air box any good? what about all of the air behind that bellmouth? that is why the el box has it incorporated in the adaptor at the back. the only reason i can see ford put in the bellmouth is mainly to reduce induction noise, once removing it there is a big difference in noise... also, no bellmouth in the BA! 3" all the way from air box to throttle body! must be a reaon for that hey? bell mouth is useless...
_________________ 07 BF MKII XR6T |
|||
| Top | |
|||
| Walker |
|
|||
|
Yeah i removed it from my EF, i also ran a foam Finer Filter in it, everytime i cleaned the filter the dust and dirt was even across the pad, not at the corner where it sucks the air in lol.
EL__Fairmont seems to notice huge gains from every little mod he does, in that case his car must be pretty quick from his induction mods. Of all the intake mods i tried on my EF, the one that was noticable is when i drilled through the base of the air box and ran a 3 inch cold air intake down to the front bar. |
|||
| Top | |
|||
| GeZza200 |
|
||||
|
I just took a pic of it
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||||
| Top | |
||||
| FAST-XR |
|
|||
|
yeah thats it!
cut the guts out of it and open it up! should be able to take about 20mm out of the diameter! and change the pipe that attaches to it, cos thats only an extension of the bellmouth effect. the opening diametre of the 1st pipe is as small as the bellmouth itself, so get a peice of 3" pipe 200mm long and replace it.
_________________ 07 BF MKII XR6T |
|||
| Top | |
|||
| Walker |
|
|||
|
I actually used a hole saw and chopped that out, it's a nice neat way of cutting it.
|
|||
| Top | |
|||
| 613 |
|
||
|
i cannot seem to find the full article on google... could someone post a link.. thanks
|
||
| Top | |
||
| SLY40L |
|
||
|
Yes that google link would be very helpful right about now!
Last edited by SLY40L on Mon Jul 09, 2007 7:22 pm, edited 1 time in total. |
||
| Top | |
||
| ebfairmont3.9 |
|
|||
|
wouldnt this just be an easy way to get rid of the bellmouth????
_________________ 1994 ED Fairmont Champaign Gold - AU Series II Intech 4.0L - EL EFI - Thermo Fans - 4.11 LSD - Pacemaker 4480 Into Custom 3" Exhaust - Shift Kit |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 61 guests |
