|
| shoey50 |
|
||
|
just wondering if there is anyone thats knows or might know a bit about putting a ba engine into an ef etc (dont wanna hear about how much its gonna cost or waste of time blah blah blah just wanna know a bit about doing it ) cheers shoey
|
||
| Top | |
||
| fordzatmyplace |
|
||
|
you'll need a aftermarket ECU. I think its becuase the BA ECU is wired up with heaps of other stuff that the E-series isn't compatable with. Like instrument cluster, SSS and [i]smartshield[i] (Not smartlock) Immobilisation
_________________ ^^^ What He Said
|
||
| Top | |
||
| fordzatmyplace |
|
||
|
also might be a bit easier on EF due to both EF and BA being coil pack
_________________ ^^^ What He Said
|
||
| Top | |
||
| rushed |
|
|||
|
i know the bonnet needs a hole or bulge, not sure about the crossmember, gearbox.
|
|||
| Top | |
|||
| haggis |
|
|||
|
if you were to keep the EF ECU then, could you just throw in a pair of cams that aren't designed for the VCT? I'd imagine that you would have to trick the ECU into thinking that it's still only a SOHC setup etc etc but could you simply leave everything else uplugged?
_________________ I can see through wooden doors. |
|||
| Top | |
|||
| Gaz |
|
||
|
BA runs 1 coil per cylinder IIRC?
engine wont fit height wise. need buldge or hole. engine wont fit into crossmember/kframe without chopping it up.
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| dumpdef |
|
||
|
been reading a bit about this convesion wana put one in my fairmont, what are the reasons the engine doesnt fit into crossmemeber/k-frame. and if u have to does cutting these areas totally f$%k ur car and make it illegal etc etc, ne help is great.
_________________ Piss On Holden!!!!
|
||
| Top | |
||
| dumpdef |
|
||
|
like ive seen in magazines, theres a hilix with an ls1 in it surley if someone can fit an LS1 into a hilux u can fit a newer 4l ford engine into an older 4l ford,obviuolsly with a fair bit of work etc but it must be able to b done without totally f%$kin ur car
_________________ Piss On Holden!!!!
|
||
| Top | |
||
| Nicko |
|
|||
|
Yes, you need to cut crossmember to fit it, And yes this will render your car illegal/unroadworthy!
There is a unit coming out that will allow you to keep the ba ecu and use that. Id imagine you would have to sort out fuel sender also. You would need to use the ba auto too, which means you may need a different tailshaft as the length could be different If you could have the car off teh road for a couple weeks and were quite good technically you could to it! But if you are a novice that has never pulled there car apart you would stand no chance! Hope this helps
_________________ Nicko |
|||
| Top | |
|||
| stockstandard |
|
|||
|
dumpdef wrote: like ive seen in magazines, theres a hilix with an ls1 in it surley if someone can fit an LS1 into a hilux u can fit a newer 4l ford engine into an older 4l ford,obviuolsly with a fair bit of work etc but it must be able to b done without totally f%$kin ur car
Fitting different engines into 4x4's is easy because the engine bays are huge and there is no k-frame. Unlike the BA 6's, LS1's are also very simple engines (no fancy DOHC VCT, drive-by-wire, etc). Also lots of aftermarket support for engine conversions for 4x4's. As far as the BA into anything else, there are so many threads already on this topic - do a search.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| bogan393 |
|
|||
|
It is deffinately possible to do, jetxr has a ba xr6t motor paired up with a toploader in his ef/el, going to a manual like that is prob the best way of doing it then you can run something like a wolf as a stand alone ecu. There are some places now that are starting to sell items that allow ba ecus to run in non bas but im not really sure how they work.
_________________ Rides:
|
|||
| Top | |
|||
| shoey50 |
|
||
|
stockstandard wrote: As far as the BA into anything else, there are so many threads already on this topic - do a search.
ever tried doing a search in these forums worst search engine evercome up with everything but what im after!! as far as the gear box goes i heard the ef ones will bolt up not true thoughts?? and with wiring what would be easier after market or ba comp and cuting s**t dont bother me thats easy i also have 2 cars so i still have something to drive when its of the road yay |
||
| Top | |
||
| stockstandard |
|
|||
|
shoey50 wrote: stockstandard wrote: As far as the BA into anything else, there are so many threads already on this topic - do a search. ever tried doing a search in these forums worst search engine evercome up with everything but what im after!! Sure have. Often takes me nearly an hour to get what I need but still quicker that waiting for sombody else to tell me the answer.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| EFFalcon |
|
|||
|
BA's run coil on plug, so you're up for BA ECU or aftermarket ECU.
kframe will 100% need modification, similar to what needs to be done to get an AU engine in an eseries. bonnet will need cutting, weather it be the bonnet frame or skin depends on what bonnet you're using. the rocker cover clears the bonnet skin but not the frame, how ever when the engine torques up you'd risk it hitting the bonnet. EF auto will *somewhat* bolt up apparently, you'd need to retain a number of the stock EF sensors to ensure proper operation. Don't know if the BA ECU can control the EF transmission, but as with aftermarket ECU you could keep the stock ECU with the new ECU. EF/EL throttle body should go straingt on the manifold and allow cable usage.
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| shoey50 |
|
||
|
thanks mate exactly what i needed to hear cheers
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 89 guests |
