|
| bry40l |
|
|||
|
a friend of mine thinks all thats needed to fit the ba engine into E series is to "shave the sump a tad" and "custom engine mounts" surely it takes more than this from wat ive read on this forum?
_________________ BF XR6 |
|||
| Top | |
|||
| TROYMAN |
|
||
|
if you did a search you would have found quite a few threads on this...
its not quite that simple,the ba sump cannot be modified enough to clear the k frame, so a modified k frame is needed. and the e series engine mounts will fit fine, the more complex bit is getting it to run.... |
||
| Top | |
||
| bry40l |
|
|||
|
well i read about it a while ago and just wanted to have some 1 elses word to back me up, thanks just made this guy feel about 2 foot tall haha
_________________ BF XR6 |
|||
| Top | |
|||
| TROYMAN |
|
||
|
he reason the ba sump cannot be modified is the ba oil pump is at the front of the sump and there is a bulge cast into the sump to clear the oil pump...
|
||
| Top | |
||
| Lowlane7 |
|
||
|
TROYMAN wrote: he reason the ba sump cannot be modified is the ba oil pump is at the front of the sump and there is a bulge cast into the sump to clear the oil pump... Not tryin to undermine you there troyman, but what about this? ford-4l-and-6-cylinder-f1/au-sump-mod-for-e-series-t79648.html I thought the pickup was too far foward too. This is spinning me out though unless the pickup from a EL bolts to the AU block the same like what would be in a hybrid motor... Or a customized pickup...
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| TimmyA |
|
|||
|
Thats an AU sump, not a BA/BF sump if that makes any difference...
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| Lowlane7 |
|
||
|
Ohk, my new thing learned for the day.
I thought AU/BA had same/similar bottom end design.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| TimmyA |
|
|||
|
it very well may... I have no idea... just sticking my 2c worth in...
 I thought they'd be nothing alike going from SOHC to DOHC and everything else about seemed different...
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| Lowlane7 |
|
||
|
That makes sense. New engine design.
They look similar from the outside.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| TROYMAN |
|
||
|
Lowlane7 wrote: TROYMAN wrote: he reason the ba sump cannot be modified is the ba oil pump is at the front of the sump and there is a bulge cast into the sump to clear the oil pump... Not tryin to undermine you there troyman, but what about this? ford-4l-and-6-cylinder-f1/au-sump-mod-for-e-series-t79648.html I thought the pickup was too far foward too. This is spinning me out though unless the pickup from a EL bolts to the AU block the same like what would be in a hybrid motor... Or a customized pickup... yea thats the au into e series.. in au the oil pump runs off the aux shaft like e series, where ba dont have the aux shaft like au and the oil pump is right at front of the block.. |
||
| Top | |
||
| Lowlane7 |
|
||
|
Has now been edjamakated.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 100 guests |
