|
| glenneaux |
|
||
|
how much clearance is required to clear an eb2 k-frame?
Its expendable so will a slegdgehammer suffice? |
||
| Top | |
||
| ringastinga |
|
||
|
|||
| Top | |
||
| glenneaux |
|
||
|
blah, that doesnt help.
if you'd read it you'd know that i've posted in that thread, fool. |
||
| Top | |
||
| Dansedgli |
|
||
|
Weld some box to the front of the crossmember then cut the original away.
|
||
| Top | |
||
| glenneaux |
|
||
|
Dansedgli wrote: Weld some box to the front of the crossmember then cut the original away.
yeah thought about that but i dont have a welder and dgaf about it just want it to bolt in 
the only way i could get it welded would be to drive the car somewhere, and i guess it cant be done with the engine in? :p |
||
| Top | |
||
| EFFalcon |
|
|||
|
sledge + grind ribs off sump?
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| Steady ED |
|
|||
|
I don't reckon you'll get enough clearance with a sledgey glenn.
Can't you borrow some kunts arc or something?
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| glenneaux |
|
||
|
EFFalcon wrote: sledge + grind ribs off sump? hehe i'd rather damage the k-frame more than the sump  Steady ED wrote: I don't reckon you'll get enough clearance with a sledgey glenn.
Can't you borrow some kunts arc or something? I dont know any knts with an arc welder, only migs. maybe i'll just cut it and bolt a piece of steel in the middle or something.?
I dont want to take the k-frame out or transport it by trailer. I'd rather put the motor in and drive it somewhere without the crossmember in then get it welded in after
|
||
| Top | |
||
| TROYMAN |
|
||||
|
can i suggest cut through the centre of the square tube at the front of the k frame bend each side of the tube with a sledg or a jack.
one you got the engine in and running just drive it to where ever you can get a welder and weld it back up?? that tube is only a support bar its not really structual... something like what i have done to put the au engine into the ea.. here is a pic
|
||||
| Top | |
||||
| madeaspack |
|
||
|
isnt the sump the same as au and fit pretty easily?
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| glenneaux |
|
||
|
TROYMAN wrote: can i suggest cut through the centre of the square tube at the front of the k frame bend each side of the tube with a sledg or a jack.
one you got the engine in and running just drive it to where ever you can get a welder and weld it back up?? that tube is only a support bar its not really structual... something like what i have done to put the au engine into the ea.. here is a pic did you grind the ribs off? i dont really want to damage the sump (not that grinding fins off is damage)... But thats probably what i'd do, even if i have to grind the ribs off. Thanks mate |
||
| Top | |
||
| Steady ED |
|
|||
|
Is that gonna clear BA oil pump?
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| glenneaux |
|
||
|
Steady ED wrote: Is that gonna clear BA oil pump?
who knows.. i'm sure the car would survive low speed country roads to get somewhere to get it welded without the member all together... but i'd probably be dominating the road with a ba motor and a t5 :O |
||
| Top | |
||
| TROYMAN |
|
||
|
madeaspack wrote: isnt the sump the same as au and fit pretty easily?
no the ba has a extra bulge on the front of the sump..(i think its the oil pump.. |
||
| Top | |
||
| EFFalcon |
|
|||
|
actually.... bolting it in might be an idea glenn.
Cut the middle section out so you've got clearance. get some square steel and drill both, few bolts through and done. drive and get it welded up.
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 126 guests |
