|
| clampy |
|
||
|
changed my rotors and pads and trying bleeding brakes like the manual says buts i just cant get the air out any one got any ideas and the brake fluid is topped up......
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| asizzy |
|
||
|
Air coming out on all sides? or just one side? Maybe forgot to close back the nut?
_________________ AsIzZy |
||
| Top | |
||
| clampy |
|
||
|
all of em just softest pedal
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| BubbyGetPizzaForCat |
|
||
|
A few days ago, I had a situation where the electrical switch on the master was leaking, and wouldnt bleed properly. Check for leaks.
Order which you bleed them, drivers front first, front pass, drivers rear, pass rear... I think... I found the only way to do it on my own, is get some clean plastic hose (about 50cm) that fits snugly on the bleed nipple. Get a clean small glass jar with some new brake fluid in it, and put the other end of the hose in it. It works like the reverse of how a bong works, you can blow air down the cone but if you sucked the cone you'd get a mouthfull of bongwater. Hope this has helped, or at least been funny... |
||
| Top | |
||
| nalane |
|
|||
|
You didn't need to crack the brake lines to do rotors and pads.
Useualy start with the wheel furthest from the master cylinder then work closer. |
|||
| Top | |
|||
| clampy |
|
||
|
yeah i started from the furtherst brake.... now u explained it in bong terms i understand lol
so when u put the hose and that in the fluid u crack and just press the pedal in slowely and release or just keep pumping slowely???
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| eb xr6 falcon |
|
||
|
Just keep pumping the brake until clean brake fluid flows out then push the brake all the way in. Hold it and get someone to lock the bleeder do that on all brakes starting from the furtherest and work your way to the closest to the brake booster.
|
||
| Top | |
||
| clampy |
|
||
|
ok will do thanx mate
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| cp1pgo |
|
|||
|
basically go
left hand rear right hand rear left hand front right hand front. its possible there could be a small crack in the brake line letting air in.
_________________ 1995 EF Ford Falcon Fairmont |
|||
| Top | |
|||
| nalane |
|
|||
|
You can get bleeders with one way valves on the end but have never used them.
|
|||
| Top | |
|||
| asizzy |
|
||
|
where can you get these one way valves from?
_________________ AsIzZy |
||
| Top | |
||
| peaandham |
|
|||
|
Sprint Auto Parts, Auto Pro, Autobarn, any good place should have them
_________________ OLD CAR: EB II Falcon, Everglade Green, 250thous (Rough Guess), Wildcat Extractors, 2.5 Exhaust with Muffler + Hot Dog, 18 Inch Rodney Jane Mags, XH Snorkel, EA MPEFI Tubing ! |
|||
| Top | |
|||
| nalane |
|
|||
|
Autobarn, repco maybe even supercrap.
|
|||
| Top | |
|||
| asizzy |
|
||
|
Its easy to replace right? Just take the old bleeder screw thing totally out and replace?
_________________ AsIzZy |
||
| Top | |
||
| nalane |
|
|||
|
No they do not replace the bleed nipple they are a rubber tube with a one way valve on the end.
You can buy speed bleeders that replace the nipples but I would ask someone who has used them if they are any good. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 96 guests |
