|
| madmax |
|
|||
|
Till_Lind wrote: madmax wrote: Till_Lind wrote: madmax wrote: Replace the clamps, you should be able to replace them without removing the hose. That way you wont lose all your coolant. If you find you really need to remove the hose you can siphon most of the coolant out. And don't forget to set the video camera up first, just in case.  How the fudge do you do that though man? Syphon it out I mean? Because I tried that before with a garden hose in the surge tank (from the top). Garden hose is too big! you need some small clear tubing. Where could I get that from, Repco? And where should I insert it? Hardware stores. Insert it into header tank and down into hose that goes into radiator tank around halfway. From here you will be able to syphon out approx 1/2 of your coolant. Remove top hose from radiator, insert tubing down tank as far as you can. You should be able syphon out most of the coolant from here. I did this when I replaced my water pump, hardly lost a drop.
_________________
|
|||
| Top | |
|||
| Rick_Deckard |
|
|||
|
madmax wrote: Till_Lind wrote: madmax wrote: Till_Lind wrote: madmax wrote: Replace the clamps, you should be able to replace them without removing the hose. That way you wont lose all your coolant. If you find you really need to remove the hose you can siphon most of the coolant out. And don't forget to set the video camera up first, just in case. How the fudge do you do that though man? Syphon it out I mean? Because I tried that before with a garden hose in the surge tank (from the top). Garden hose is too big! you need some small clear tubing. Where could I get that from, Repco? And where should I insert it? Hardware stores. Insert it into header tank and down into hose that goes into radiator tank around halfway. From here you will be able to syphon out approx 1/2 of your coolant. Remove top hose from radiator, insert tubing down tank as far as you can. You should be able syphon out most of the coolant from here. I did this when I replaced my water pump, hardly lost a drop. Cheers b2u mate.
_________________ E39 523i |
|||
| Top | |
|||
| The Dog |
|
|||
|
Make sure the tube coming out on both ends is real clean before the hose is put back on. Dunno Bout the later models (different induction) but on the EA and Bs there is an allen key head bolt on the thermostat housing (passenger side). Remove the bolt and fill the colling system until it runs out here. Put thread tape or sealant back on bolt and replace and finish filling cooling system. Thats the official way. The other way is to fill it up, leave cap off, and run till warm, Squeeze top hose, bubbles should come out in the surge tank. Do this until all bubles are out. Not sure how succesful the second method is.
Please make sure you have somone videotaping the above mentioned. Funniest home videos pay a fairbit for good videos!!! 
_________________ You'll ride a black tornado across the western sky
|
|||
| Top | |
|||
| Jim Beam |
|
|||
Age: 35 Posts: 3505 Joined: 1st May 2005 Ride: EB Fairmont Location: Northern Suburbs, Adelaide |
Dont lock yourself under the hood
_________________ Doin it for Scotty. |
|||
| Top | |
|||
| twr7cx |
|
|||
|
stuff reusing your water, put the nice clean stuff in, when you take the old lot out it'll help to clean out any muck or anything that's in there.
|
|||
| Top | |
|||
| madmax |
|
|||
|
twr7cx wrote: stuff reusing your water, put the nice clean stuff in, when you take the old lot out it'll help to clean out any muck or anything that's in there.
Its not that old. He only did it a couple of weeks ago.
_________________
|
|||
| Top | |
|||
| madmax |
|
|||
|
xhute0 wrote: Make sure the tube coming out on both ends is real clean before the hose is put back on. Dunno Bout the later models (different induction) but on the EA and Bs there is an allen key head bolt on the thermostat housing (passenger side). Remove the bolt and fill the colling system until it runs out here. Put thread tape or sealant back on bolt and replace and finish filling cooling system. Thats the official way. The other way is to fill it up, leave cap off, and run till warm, Squeeze top hose, bubbles should come out in the surge tank. Do this until all bubles are out. Not sure how succesful the second method is.
Please make sure you have somone videotaping the above mentioned. Funniest home videos pay a fairbit for good videos!!! The second way is the official way. Lest thats what the sticker said on the surge tank of my EA.
_________________
|
|||
| Top | |
|||
| The Dog |
|
|||
|
Thats interesting to know madmax cos the Max Ellery manual is where I got the other info. I'd always done it the second way until I read the manual (you know: what you do after you have f**k it up!
)
_________________ You'll ride a black tornado across the western sky
|
|||
| Top | |
|||
| falcon4litreOHC |
|
|||
|
I replaced that hose about 2 months ago, i reused the hose clamps etc and it never leaked. Did you put the hose around the right way.
The one i got had an internal wire and was shaped to fit with an arrow marking radiator end and arrow marking water pump end. cheers. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 70 guests |
