|
| ThaJFactor |
|
||
|
Hey all and welcome to my first post!!..
Well here is my problem that I am needing you opinion on.. I'm getting a fair bit of blue smoke when I first start my EB 4.0 in the morning.. I bought the car with a blown head gasket, which was replaced and the head and block were checked and found to be "true" and there appears to be no visible cracks in either.. I came to the conclusion that the valve stem seals were stuffed, so they were replaced.. Only issue is that, although the smoke issue isn't as bad as it first was, it is still there.. What else should I have a look at to figure out what is going on??.. Leaky injector maybe??.. It is definately blue smoke not clear white.. The car is using no water and very little oil (hardly noticable consumption).. Also there is no mixing of oil and water occuring.. It clears up after about 5 km of driving or about 10 mins at idle.. Thank in advance for your help.. |
||
| Top | |
||
| Disco Frank |
|
|||
|
well i would be going with valve stem seals as well
a leaky injector would give black smoke ( as in rich fuel mix ) blue smoke is oil! unless the rings are shot i would going back to teh shop and tellign them to fiox it
_________________ RIP SCOTT |
|||
| Top | |
|||
| ringastinga |
|
||
|
as frank said, blue smoke = oil and being only at start-up i point my finger straight towards the stem seals... i know u said they were replaced but i recon not properly
|
||
| Top | |
||
| ringastinga |
|
||
|
rings would give constant smoke... do a compression test if all good back to the shop
|
||
| Top | |
||
| ThaJFactor |
|
||
|
Thanks for the replies.. Did the job myself so no shop involved to take it back to.. Only had a shop check the head and block for warping..
Could it be leftover oil from soaking the seals??.. Only did the job yesterday and it only did it this morning.. I agree about the injectors.. Only reason I asked is that IIRC unburnt fuel also comes out as white smoke, but I will happily stand corrected.. |
||
| Top | |
||
| Disco Frank |
|
|||
|
ohh the job was done yesterday...
yes could be leftover oil from them soaking give it a few days and see how it is
_________________ RIP SCOTT |
|||
| Top | |
|||
| XRfairmont67 |
|
|||
|
maybe valve guides are worn
|
|||
| Top | |
|||
| ThaJFactor |
|
||
|
Quick update for you all.. I started the old girl this morning and she still had issues.. The EB still had a smoke issue too!!..
Nah in all seriousness, I'm probably erring in the side of the guides for being my problem unless it is something else.. Is there a quick fix i could use to allay the smoke for a couple of weeks??.. An additive or something??.. Only need it to die down until I go on holidays from work.. |
||
| Top | |
||
| ThaJFactor |
|
||
|
Ok well here we go with a stupid question.. IF a small bit of gasket/old sealant was left on either surface at time of the head gasket change would this possibly give the same symptoms??.. I'm only clutching straws here, but I've tried most of the things mentioned but no love.. The only thing I haven't done is change the guides..
|
||
| Top | |
||
| mitchg911 |
|
|||
|
does it blow smoke when you have high inlet vacuum? ie when you use the gears to slow down?
if its valve stem seals it will blow smoke then also.. take it for a drive get upto say 60-70 and pull it back a couple of gears.. if it doesnt do it then id go looking elsewhere -mitch
_________________ BF XR6T 6spd Auto. 60lb injectors, Hybrid Cooler, Custom Piping, Custom Surge Tank, Actuator. |
|||
| Top | |
|||
| ThaJFactor |
|
||
|
mitchg911 wrote: does it blow smoke when you have high inlet vacuum? ie when you use the gears to slow down?
if its valve stem seals it will blow smoke then also.. take it for a drive get upto say 60-70 and pull it back a couple of gears.. if it doesnt do it then id go looking elsewhere -mitch Yeah replaced stem seals, but same issue.. I have no oil being dragged in to the inlet either.. Still not using any oil or water.. |
||
| Top | |
||
| teveo |
|
|||
|
Giudes and seals definatly..
_________________ <a href="http://s154.photobucket.com/albums/s278/stephen351/?action=view¤t=resize2.jpg" target="_blank"><img src="http://i154.photobucket.com/albums/s278/stephen351/resize2.jpg" border="0" alt="resize"></a> |
|||
| Top | |
|||
| TickXR |
|
|||
|
More than likely worn guides, if you've replaced the seals properly and still smoking then obviously oil getting down into combustion chamber from somewhere
Also do a compression test on your cylinders, if you have cracked ring or busted ring land it will show up in figures
_________________ If you don't do it whilst your livin, you aint got no bloody chance when your dead!!! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 51 guests |
