|
| Campbell18 |
|
|||
|
now that ive finally got the shims, im looking at installing my wade 1636
im not to keen on doing it myself since iv never replaced a cam before and i dont particularly want to stuff anything up  if i was to get it done at the mechanics roughly how much would i be up for?? although iv heard that the 1636 runs on both the standard computer and springs is it worth looking at a j3 chip to get the most out of the cam or is this just a waste of money?? cheers
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| phongus |
|
|||
|
Campbell18 wrote: now that ive finally got the shims, im looking at installing my wade 1636 im not to keen on doing it myself since iv never replaced a cam before and i dont particularly want to stuff anything up if i was to get it done at the mechanics roughly how much would i be up for?? although iv heard that the 1636 runs on both the standard computer and springs is it worth looking at a j3 chip to get the most out of the cam or is this just a waste of money?? cheers You should be able to get away with just the stock ECU...if you have the extra money I guess you can get the J3 chip. I suggest getting a Vernier Camshaft Sprocket first though, it's a relatively cheap tuning gear if you want aftermarket camshafts to run well. Not sure how much it would cost to install a camshaft, but I would assume $100 or more.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Campbell18 |
|
|||
|
okey dokey
anything just over $100 sounds pretty reasonable how much is a vernier gear worth roughly? if i was to have a crack myself is there any tech docos i could use as a guideline? apparently its pretty straight forward, but ive never taken the rocker gear apart before so im not to sure wats involved cheers
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| WagonDad |
|
|||
|
I recon most mechanics would allow two hours to install a cam in the SOHC I6, more to dial it in, budget for at least two hours at the rate charged where ever you get the work done.
_________________ 4.0L EF Fairmont Station Wagon. EL GT Snorkel. K&N Pod in air box. 3" Intake piping.
|
|||
| Top | |
|||
| krisisdog |
|
|||
|
Mate with Wade cams theyre drop in and go, dont worry about the vernier gear if your strapped for cash or dont plan on changing cams again.
With the $ saved, get a J3 instead! |
|||
| Top | |
|||
| dahayes |
|
||
|
Campbell18 im in the same siuation myself mate if you do have a go at it ill be interested to hear how you went..
|
||
| Top | |
||
| toddy69 |
|
||
|
how much does a wade 1636 cost??
|
||
| Top | |
||
| Campbell18 |
|
|||
|
i got mine second hand from a fellow fordmodder
im pretty sure its around $150 for a regrind from wade cams you'll need to allow another $40 or so for shims on top of that though
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| adam_k |
|
|||
|
hi guys, sorry to hi-jack but don't see a point in starting a new thread, and just want to know a few things about my own install.
dropping in a crowcam into my AU, its going into a brand new! AU engine. just wondering what other things i'll need to get it in. (shims, vernier gear, springs?) cheers |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 38 guests |
