|
| bryce67 |
|
||
|
could some 1 plz give me a step by step giud to installing my new cam
_________________ 1992 falcon eb manual xr6 minor head work j3 chip tuned to a el xr6 manual ecu pushing 130rwkw |
||
| Top | |
||
| SWC |
|
||
|
|
||
| Top | |
||
| bryce67 |
|
||
|
ok came across a little predicament the new cam i got has been regrounded so i need to put more shims right? and if so how many just an extra 1 and are shims the metal circle inside the tip of the rocker arm plz some 1 help also the cam tensioner chain weres the bolt to decrease tenshion on chain so i can swap the cams or is there anouther way to do it the doco up from this post dosnt go that much into detail also what torqe is needed for bolts on rocker
_________________ 1992 falcon eb manual xr6 minor head work j3 chip tuned to a el xr6 manual ecu pushing 130rwkw |
||
| Top | |
||
| snap0964 |
|
|||
|
SWC wrote: Maybe we need a Wiki......................  snap0964 wrote: Most of the basic stuff has been covered here numerous times - most people though are too lazy to search for it - they'd rather be spoon fed.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| TROYMAN |
|
||
|
the most effective way to get that cam in the engine is to stand infront of the engine, if your right handed stand with your left foot slightly forward, get the cam in your right hand and raise it just above your head and throw it as hard as you can, you need to throw it hard enough to get it through the rocker cover, so it might take a few attempts ,once it breaches the cover your done... happy motoring....
 sorry i could help my self.... im having a silly day..... |
||
| Top | |
||
| phongus |
|
|||
|
SWC wrote: http://www.fordmods.com/documents.php?d=59 Maybe we need a Wiki...................... Even with a wiki, they will probably still ask rather than search. FM search by all means isn't the best, but it still works. Even using google with fordmods.com as the website tag will get you a lot of hits! You can read this head gasket document...has camshaft installation in it, using a regrind. Ignore the tensioner bit, still need to fix/refine that. fordmods-technical-documents-diy-f38/head-gasket-doco-t99962.html For the tensioner, look at these threads... ford-4l-and-6-cylinder-f1/timing-chain-tensioner-t117619.html ford-4l-and-6-cylinder-f1/timing-tensioner-troubles-t95193.html ford-4l-and-6-cylinder-f1/timing-chain-tensioner-seal-t99338.html
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| SWC |
|
||
|
bryce67 wrote: ok came across a little predicament the new cam i got has been regrounded so i need to put more shims right? and if so how many just an extra 1 and are shims the metal circle inside the tip of the rocker arm plz some 1 help also the cam tensioner chain weres the bolt to decrease tenshion on chain so i can swap the cams or is there anouther way to do it the doco up from this post dosnt go that much into detail also what torqe is needed for bolts on rocker A few points for you to consider........... 1) Punctuation is a wonderful thing, it allows us normal people (or not so normal) to understand what you are trying to say. 2) Yes you need 2 shims per rocker, your original one and an additional one. 3) If you arn't sure what a shim is, don't touch the cam............ 4) Buy a workshop manual, it contains all the information you require. |
||
| Top | |
||
| SWC |
|
||
|
phongus wrote: SWC wrote: http://www.fordmods.com/documents.php?d=59 Maybe we need a Wiki...................... Even with a wiki, they will probably still ask rather than search. FM search by all means isn't the best, but it still works. Even using google with fordmods.com as the website tag will get you a lot of hits! To Phong & Snap My reference to the "Wiki" was sarcasim as I was 1 of the few that upset the OP in that original "WIKI" Thread. I just can't help myself 
|
||
| Top | |
||
| phongus |
|
|||
|
SWC wrote: phongus wrote: SWC wrote: http://www.fordmods.com/documents.php?d=59 Maybe we need a Wiki...................... Even with a wiki, they will probably still ask rather than search. FM search by all means isn't the best, but it still works. Even using google with fordmods.com as the website tag will get you a lot of hits! To Phong & Snap My reference to the "Wiki" was sarcasim as I was 1 of the few that upset the OP in that original "WIKI" Thread. I just can't help myself There's a wiki thread?
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| SWC |
|
||
|
|
||
| Top | |
||
| snap0964 |
|
|||
|
SWC wrote: To Phong & Snap My reference to the "Wiki" was sarcasim as I was 1 of the few that upset the OP in that original "WIKI" Thread. I just can't help myself Hence why I quoted myself from that thread.  Just don't scare away newbies that have some ideas and want to be proactive. They're a rare commodity around these neck of the woods . . . . . .
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| EF_wanabe |
|
||
|
I have noticed alot of the guides have got the lifter assembly using tape to hold the hydro shims in place
I ended up moving the arms upwards so there about straight into the air then bolted the assembly in gently and moved the rocker arms down so the shims go into place ( already fitted) |
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
its easy to keep the rocker arms pointing straight up.......... that is until theyre resting on the lobes of the cam which pushes them over and lifters falling out everywhere
tape is king, just remember to pull each bit of tape off before you tighten the bolts too much or you cant pull the tape out
|
||
| Top | |
||
| EF_wanabe |
|
||
|
FordFairmont wrote: its easy to keep the rocker arms pointing straight up.......... that is until theyre resting on the lobes of the cam which pushes them over and lifters falling out everywhere tape is king, just remember to pull each bit of tape off before you tighten the bolts too much or you cant pull the tape out Hmm i must have got real dam lucky then |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 91 guests |
