|
| easpak1 |
|
||
|
Im after someone who can install a rpd stage 2 cam for me.
Im near Caboolture so if anyone here willing to do this and is on the sunshine coast or near Caboolture,Queensland? Last edited by easpak1 on Sun May 28, 2006 7:07 am, edited 3 times in total. |
||
| Top | |
||
| MARK.TANIA |
|
||
|
it is a pity you are up there ''if were closer i would put it in for you no worries
|
||
| Top | |
||
| easpak1 |
|
||
|
thanks for that mark
How far is orange from the border lol thinking of driving down there |
||
| Top | |
||
| wicksy |
|
|||
|
i wouldnt drive to orange,she is a fair drive, you should be able to find someone round your area, its would be over10hrs to get down there
_________________ Now i have a EF XR8 5spd.........mmmmmm 5L |
|||
| Top | |
|||
| justfordima |
|
|||
|
Orange is a bit far lol.. Have you looked through Jaysens tutorial on installing cams?? Its not as hard as it all seems to be. Its fair enough if you don't feel confident (and at one stage we all were).. but just a though.
Cheers
_________________ ;++JustForDimSim++;
|
|||
| Top | |
|||
| EB91XR6 |
|
|||
|
its realy easy i changed mine again thismorning and i ended up cracking a rocker arm bolt, didnt know it was posible,
_________________ 1976 XC falcon
|
|||
| Top | |
|||
| stockstandard |
|
|||
|
EB91XR6 wrote: its realy easy i changed mine again thismorning and i ended up cracking a rocker arm bolt, didnt know it was posible,
Same thing happened to me the other week. Had the torque wrench at just 15nm and one of the rocker bolts snapped.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| justfordima |
|
|||
|
They aren't the strongest things in the world, but it shouldn't really happen. Did you have it set on the dowels properly.. and did you do them up in stages?
Cheers
_________________ ;++JustForDimSim++;
|
|||
| Top | |
|||
| stomper |
|
|||
|
I think at the wrecker they were fitting AU rockers and bolts to th EFs. I THINK
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
| Top | |
|||
| stockstandard |
|
|||
|
justfordima wrote: They aren't the strongest things in the world, but it shouldn't really happen. Did you have it set on the dowels properly.. and did you do them up in stages?
Cheers Yes it was all seated fine, and yep i was doing it up in stages (15nm is what the torque wrench was set at when it snapped, 25nm is the torque spec on rocker gear bolts). Done it heaps of times before and never had problems. I couldnt believe it when it snapped. The bolts all looked fine, just the one that snapped with 0 force on it (less than 15NM anyway). No big deal though, pulled the gear off, extracted the broken thread, back on with different set of bolts and all fine.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| MARK.TANIA |
|
||
|
yes it is a good 10 hours to orange and it is getting bloody cold too. you should be able to find some one near you to put it in for you. see if your dads machanic can do it for you cheep
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 79 guests |
