|
| au man |
|
|||
|
Hey
I have just pointed my rocket cover on my Ford AU, now i have put it all together i started it up, and it doesn't idle right. If its in park or neutral it revs at 2000rpm+, but when i put in drive or reverse it goes down to normal which is about 900rpm.  What is the problem?
Thanks |
|||
| Top | |
|||
| wobbo |
|
||
|
idle speed controller? didn't paint it on the car did you?? had a guy at work do that and got some s**t in his tb
_________________ ONE FOR RUM AND RUM FOR ALL
|
||
| Top | |
||
| MacGyver |
|
|||
|
Did you disconnect or knock any vacuum lines? Disconnect the ISC and not hook it up properly. Disconnect battery and ECU needs to relearn? Disconnect accelerator or cruise cable and it is not hooked up right?
Lots of things to go through. You could also reset the idle speed by putting car into diagnostics, disconnect ISC and put 0.75mm feeler between the idle screw. Set idle for 650rpm. cheers Scott
_________________ If it doesn't fit, jam it. If that doesn't work use a hammer. - Engineers Motto |
|||
| Top | |
|||
| au man |
|
|||
|
Nah
 i took it off the car. As far as i know everything is plugged in right, thanks for the tips i check it in the morning.
|
|||
| Top | |
|||
| steve351 |
|
|||
|
kick it
_________________ http://www.thefordsite.com/rickkellyisacheat.html
|
|||
| Top | |
|||
| au man |
|
|||
|
Tried that ended up hearting my foot, got any other ideas. And BTW the hammer doesn't work.
|
|||
| Top | |
|||
| au man |
|
|||
|
If i disconnect all the sensors on the TB it still itels the same. If you have it in park then change it to drive something in the diff or the Tail shaft knocks. Also if you have your foot on the break the car goes faster, by that i mean it actually picks up speed.
|
|||
| Top | |
|||
| Slick |
|
|||
|
map sensor vacuum hose disconnected or leaking.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| au man |
|
|||
|
Whre is that hose is it on the TB?
|
|||
| Top | |
|||
| au man |
|
|||
|
The item that i have circled is that anything? Its like a plastic nob.
|
|||
| Top | |
|||
| Slick |
|
|||
|
au man wrote: The item that i have circled is that anything? Its like a plastic nob.
oops.. the AU is mounted directly to the plenum, theres no hose to it. check the two hose next to it. its the little black box thinggy just below the T/B.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| mr_sperm1 |
|
|||
|
au man wrote: The item that i have circled is that anything? Its like a plastic nob.
that's just a cap over the breather on the ISC
_________________ Maloo - Holden's word for ugly. |
|||
| Top | |
|||
| au man |
|
|||
|
Thats for your Help, i fixed it. If you take the TB off, the is a black plastic thing on the back that was out of place. Once i put it in place it was Fine. Once again Thanks
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 80 guests |
