|
| TimmyA |
|
|||
|
yeah the wires that disconnect the starter and prevent from starting... When the smartlock thingo is blinking that relay is opened preventing the starter solenoid from engaging (by hot wiring or the sort)
PART EDIT As I see it your actually doing the hard part for them... Unless you've got your own fail safe installed? Like a button you have to hold in to start (ie a broken injector pulse or something and once started the relay holds in helping injector pulse)?
_________________ 93 Red ED 5spd Manual Build Thread Last edited by TimmyA on Tue Jun 01, 2010 1:52 pm, edited 1 time in total. |
|||
| Top | |
|||
| effalcon94 |
|
||
|
hey guys was wondering if i replace my BCM can i put in a higher model one from say a fairmont? this weekend ill be looking at it and be seeing if i can solder them two wires together that was mentioned before... what are the dwon sides of me just soldering these wires together rather than replacing it?
|
||
| Top | |
||
| 89.SVO |
|
|||
Age: 35 Posts: 3382 Joined: 11th Mar 2008 Ride: EA SVO, AU2, Toyota Crown Location: Bendigo |
i just thought i'd post my HELPFUL tip up. but if noone wants to be use it fine by me
_________________ Daily driver: 2010 Toyota Crown hybrid 3.5L V6 hybrid. 254kw. |
|||
| Top | |
|||
| TimmyA |
|
|||
|
Actually I do appologise... the ED has separate smartlock module and BEM... Do the EF/EL models have both modules in one?
if so you will find it hard to replace with a high series unit (assuming your and EF driver) as the BEM's on the Ef's have a different amount of plugs/or pins for the class variants (low, mid and high series) plus you'll need the wiring and modules to go around it (Ie the dimmer for the dash works different on a EF/EL high series to a EF/EL mid series (I think, not 100% sure for EF/EL variants?))... But I am fairly sure you would be able to straight swap with a high series... like I said down side is I am nearlly positive you removing the smartlock immobilisation (or part of it?) by doing this... We all know smartlock is far from perfect... So is any mass rolled out immobilisation system installed in cars really... Once you know how to beat one you can steal all cars of that sort the same way... The best system for immobilisation really is something you devise and install that no criminal will be able to work out (something out of the normal that takes more time to diagnose)... If the simple trick they used last time don't work then they aren't likely to spend too much time on it for fear of getting caught...
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| TimmyA |
|
|||
|
WILDEB wrote: i just thought i'd post my HELPFUL tip up. but if noone wants to be use it fine by me no need to be like that... it definitely works... I 100% agree to that... its a simple cheap solution to the problem and guaranteed never to fail again... I was always under the impression your undoing what smartlock does thats all? Although I'm not 100% familiar if the circuit isolates anything else on top of the starter? PART EDIT
_________________ 93 Red ED 5spd Manual Build Thread Last edited by TimmyA on Tue Jun 01, 2010 1:53 pm, edited 1 time in total. |
|||
| Top | |
|||
| effalcon94 |
|
||
|
wait im stil confused on which 2 wires to solder guys? pictures mayb?
cheers...anthony |
||
| Top | |
||
| 89.SVO |
|
|||
Age: 35 Posts: 3382 Joined: 11th Mar 2008 Ride: EA SVO, AU2, Toyota Crown Location: Bendigo |
it's either blue with red stripe or red with blue stripe. one goes into the BCM and the same colour come back out. same plug. just bare both wires. solder a bit of wire between the two and it'll start fine
_________________ Daily driver: 2010 Toyota Crown hybrid 3.5L V6 hybrid. 254kw. |
|||
| Top | |
|||
| effalcon94 |
|
||
|
ahk now i ge ya mate ill try that on the weeknd...just any old wire?
|
||
| Top | |
||
| 89.SVO |
|
|||
Age: 35 Posts: 3382 Joined: 11th Mar 2008 Ride: EA SVO, AU2, Toyota Crown Location: Bendigo |
effalcon94 wrote: ahk now i ge ya mate ill try that on the weeknd...just any old wire? half decent wire would be better. not just some wire you had kanging around
_________________ Daily driver: 2010 Toyota Crown hybrid 3.5L V6 hybrid. 254kw. |
|||
| Top | |
|||
| TimmyA |
|
|||
|
EDIT
_________________ 93 Red ED 5spd Manual Build Thread Last edited by TimmyA on Tue Jun 01, 2010 1:50 pm, edited 1 time in total. |
|||
| Top | |
|||
| 89.SVO |
|
|||
Age: 35 Posts: 3382 Joined: 11th Mar 2008 Ride: EA SVO, AU2, Toyota Crown Location: Bendigo |
nah EF. same colour. yeh i'm like 80% sure its reb with blue trace
_________________ Daily driver: 2010 Toyota Crown hybrid 3.5L V6 hybrid. 254kw. |
|||
| Top | |
|||
| TimmyA |
|
|||
|
they do have the smartlock and BEM in the one module? under the heater controls?
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| nalane |
|
|||
|
EDIT
Last edited by nalane on Fri Mar 19, 2010 10:44 am, edited 1 time in total. |
|||
| Top | |
|||
| effalcon94 |
|
||
|
so nalane its them wires i solder?
|
||
| Top | |
||
| XRfairmont67 |
|
|||
|
these little tricks about joining wires etc are normally only mentioned in pm's, as dodgy people do get on sites to learn ways around security
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 87 guests |
