|
| NC 5ltr |
|
|||
|
ey all
wondering how hard or easy would it be to replace crankshaft bearings as the ones in my 6cyl has about 3-5mm play in it and from what ive heard its basically labour that is the big pocket burner cheers
_________________ "Looking at cleavage is like looking at the sun. You don't stare at it. It's too risky. You get a sense of it and then you look away."
|
|||
| Top | |
|||
| tickford_EB |
|
|||
|
not sure, but id say that means pulling the engine out and apart. (nice and expensive) How do you know theres play in it, can you hear it, or is the balancer wobling about?
i spsode that means its time for a performance rebuild hey??? 
_________________ '92 XR6 (Flame Red)
|
|||
| Top | |
|||
| stockstandard |
|
|||
|
3-5mm play on the crank???
Not hard if you have the tools (and have some idea as to what your doing), but if your replacing the crank bearings you may as well do the rod bearings as well as the rings. No point stopping there so do the timing gear and oil pump, list goes on...
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| christopher |
|
||
|
i replaced mine a couple months ago its not as bad as it looks but its a engine out job and not that pricey i changed the rod,crank bearings,high volume oil pump,timing chain and tensioners and with seal+gaskets its was about $300 and thats trade price.and a couple of days.
|
||
| Top | |
||
| twase |
|
|||
|
NC 5ltr wrote: ey all If its 3-5 mm endplay and its an EF I6 then it's almost certain the crank will need replacing. There were a batch of cranks that were soft and wore quicker than the bearing material. I replaced my whole motor recently because of this issue even though the bore still showed the original hone marks.
wondering how hard or easy would it be to replace crankshaft bearings as the ones in my 6cyl has about 3-5mm play in it and from what ive heard its basically labour that is the big pocket burner cheers Cheers TW.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| NFGhia |
|
|||
|
christopher wrote: i replaced mine a couple months ago its not as bad as it looks but its a engine out job and not that pricey i changed the rod,crank bearings,high volume oil pump,timing chain and tensioners and with seal+gaskets its was about $300 and thats trade price.and a couple of days.
And if I may just add, unless your radiator has had nice green stuff in it all its life pop in some nice new welsh plugs too... 
_________________ The TORQUE Monster project begins!
|
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
Good second hand EL engines go for $650 why bother ???
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| NC 5ltr |
|
|||
|
well its a second car car behind the v8 so i think ill flog it off at the auctions to some unsuspecting p plater
 (joking)
it is a 92mpefi engine not ef  i think it would be cheaper to bolt a newer engine into it ee-au
_________________ "Looking at cleavage is like looking at the sun. You don't stare at it. It's too risky. You get a sense of it and then you look away."
|
|||
| Top | |
|||
| stockstandard |
|
|||
|
EBXR8380 wrote: Good second hand EL engines go for $650 why bother ???
Because there is a reasonable change youll be buying someone elses problems.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| twase |
|
|||
|
NC 5ltr wrote: well its a second car car behind the v8 so i think ill flog it off at the auctions to some unsuspecting p plater You still have a bit of life left in her! Assuming it is an Auto then it will go untill the timing chain starts to wear a hole in the timing case, so if you plan a motor change then keep driving it until its convenient to change it.
(joking)it is a 92mpefi engine not ef i think it would be cheaper to bolt a newer engine into it ee-auCheers TW.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| Alzxg |
|
|||
|
I am in the middle of doing mine now...albeit in a panny. All parts from Bursons; good prices. That's rings, BE & Main bearings, gaskets & seals, oils, filter etc....and welch plugs...and water pump...and pulley bearings...and a/c belt. etc etc etc.
Engine has to come out.
_________________ mechanics is a never ending series of disappointments leading one to eventually become consumed with a wgaf attitude or to grow a character with the resilience and strength of drop forged steel. yaddy yaddy yah. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 69 guests |
