|
| hornet |
|
|||
|
Yes if its a regrind cam, like most of them are.
_________________ 5 Speed EL Futura
|
|||
| Top | |
|||
| uglybob |
|
|||
|
Jaysen wrote: thats a costly proceedure
my thoughts too  lifters ain't cheap!
_________________ R.I.P. Scotty |
|||
| Top | |
|||
| Rapier |
|
||
|
uglybob wrote: Jaysen wrote: thats a costly proceedure my thoughts too lifters ain't cheap!$60 a peice from fraud, times that by 12 thats $720 ouchies |
||
| Top | |
||
| Southy |
|
|||
|
ahhh yes my friends but your forgetting the discount i get on all parts
|
|||
| Top | |
|||
| Rapier |
|
||
|
at half price that would be a rip off, u shouldnt have to replace it all caus its ticking, actually mine started ticking id rather have it tick thatn replace the lifters, but i know if i could be bothered i could prob make it not tick b mucking around with it
|
||
| Top | |
||
| Slick |
|
|||
|
Rapier wrote: uglybob wrote: Jaysen wrote: thats a costly proceedure my thoughts too lifters ain't cheap!$60 a peice from fraud, times that by 12 thats $720 ouchies 11 & 14mm HLA cost $20 a peice from surecam. 12 x $20 = $240 alright! 
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| Rapier |
|
||
|
nice nice, i still dont think the probs the HLA's anyway, repco do the HLA for about $30 as well i was just quoting the ford price
|
||
| Top | |
||
| Slick |
|
|||
|
Did you reinstall them in the same order when you took them out?
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| Johnson stroker |
|
|||
|
when you did the install the cam did you check clearances? what is being said about shims is correct, since you have installed a new cam the clearances have now changed, lift your rocker cover off, any rocker that is not on rock give it a push, there should be absolute minimal movement, if you set one or two that noticably move then you need to shim it up to absorb that movement otherwise you will bash the crap out of the HLA and needlesly have to replace it, than once replaced if you don't fix it at that point. then it will need to be done again.. Jaysen has writen a DC_todd proof cam install doco. pretty pics and good explanations
can be found here http://www.altedperformance.com/cams/Ca ... lGuide.pdf have a read see if there are any steps that you don't recognise, then do em cause you probably missed it. this is not specific to ALTED cams in this doco, but give credit when credit is due.
_________________
|
|||
| Top | |
|||
| Southy |
|
|||
|
yeah finnaly found out today after talking to the ppl at ALD that i need new thicker shims, will be going in on thursday, thanks guys
|
|||
| Top | |
|||
| Johnson stroker |
|
|||
|
good that they are willing to help fix a problem even if its not their product..
top stuff boys.
_________________
|
|||
| Top | |
|||
| Southy |
|
|||
|
lol nah by AFD i mean All ford day. just asked a few ppl and got a few opinions.
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 67 guests |
