|
| alfy |
|
|||
|
hmm thats interesting what happened to your aux shaft.
i wonder where ive seen that before? 
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
| Top | |
|||
| [JETEB6] |
|
||
|
hey troy man experienced this problem after my engine swap and was a bad earth but i think you may be on to something
its possible a valve train component may not be doing its job like an exhaust valve not opening or being effected due to carbon build up maybe ? just an idea? |
||
| Top | |
||
| TROYMAN |
|
||
|
[JETEB6] wrote: hey troy man experienced this problem after my engine swap and was a bad earth but i think you may be on to something
its possible a valve train component may not be doing its job like an exhaust valve not opening or being effected due to carbon build up maybe ? just an idea? as above it was the aux shaft..... |
||
| Top | |
||
| fiend |
|
|||
|
alfy wrote: hmm thats interesting what happened to your aux shaft.
 It is interesting --- Any ideas on what did it? And is this photo adding anything to the mystery? |
|||
| Top | |
|||
| edfairmont4.0 |
|
|||
|
Hey this thread has got me scared s**t!!!!! Because i run an AU motor with a dizzy.....
Could you put in a AUX shaft from a dizzy motor into an AU block???? my au motor has done about 50,000km with a dizzy and no problems as yet... its an AU series 1 block i wonder if thats a good thing.
_________________ ED Fairmont, Ghia mock DOHC-T 11.6 @ 118 Trying to get back to the 1/4! |
|||
| Top | |
|||
| Steady ED |
|
|||
|
I don't get how they could be different, the oil pump is going to be the bigger load, and that would be the same/similar regardless of model.
I wouldn't reckon you'd find a part number difference between shafts, but stranger things have happened! Interesting stuff though! Is there an oil feed in the block for the aux shaft? Open it a bit?
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| edfairmont4.0 |
|
|||
|
Im seeming to think its not a load thing, but more like a different cut tooth.... as in they dont COMPLETELY match...... I might just pull mine down and put an ED-EL tooth on the AU shaft. usually its just a pin holding it on. -- Im hopeing im a lucky one ive been running an AU motor with a dizzy since august 06
I think ill wait for the first symptom and as soon as it misses once ill put it in the garage and pull it out. $3000 worth of motor to die because of an aux shaft fuk that!
_________________ ED Fairmont, Ghia mock DOHC-T 11.6 @ 118 Trying to get back to the 1/4! |
|||
| Top | |
|||
| fiend |
|
|||
|
[DELETED DUE TO BEING A d**k]
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
edfairmont4.0 wrote: Hey this thread has got me scared s**t!!!!! Because i run an AU motor with a dizzy.....
Could you put in a AUX shaft from a dizzy motor into an AU block???? my au motor has done about 50,000km with a dizzy and no problems as yet... its an AU series 1 block i wonder if thats a good thing. yes .. ive now fitted my au engine with a eb aux shaft.. fits perfect... mine lasted 30,000kms of hard reving before it started showing signs of trouble.. its getting a 2nd chance at life lol... |
||
| Top | |
||
| edfairmont4.0 |
|
|||
|
sweet as man thats a bit relieving! ill wait till mine shows a sign of this issue and swap it out straight away I rekon i MAY be lucky though i rekon ive probably done about 60.000km or 38 months...
_________________ ED Fairmont, Ghia mock DOHC-T 11.6 @ 118 Trying to get back to the 1/4! |
|||
| Top | |
|||
| tryandtakeme |
|
||
|
did you compression test your cylinders? i had similar problem with my I6, compresion test showed that i had a burnt out valve.
_________________ DC LTD V8 pure style |
||
| Top | |
||
| PIMP_LTD |
|
||
|
TROYMAN wrote: yes .. ive now fitted my au engine with a eb aux shaft.. fits perfect... mine lasted 30,000kms of hard reving before it started showing signs of trouble.. its getting a 2nd chance at life lol... So troyman, does this mean the AU motor will go again after a simple aux shaft swap? So a shaft failure doesn't destroy anything?
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| TROYMAN |
|
||
|
tryandtakeme wrote: did you compression test your cylinders? i had similar problem with my I6, compresion test showed that i had a burnt out valve.
yes it has 200 psi on all cyl... and the pics of the aux shaft tell the story.. |
||
| Top | |
||
| TROYMAN |
|
||
|
PIMP_LTD wrote: TROYMAN wrote: yes .. ive now fitted my au engine with a eb aux shaft.. fits perfect... mine lasted 30,000kms of hard reving before it started showing signs of trouble.. its getting a 2nd chance at life lol... So troyman, does this mean the AU motor will go again after a simple aux shaft swap? So a shaft failure doesn't destroy anything? it should be ok only the dizzy drive part had failed.. the only slight concern is the fine metal from the drive gear that could have been curculating with the oil... |
||
| Top | |
||
| edfairmont4.0 |
|
|||
|
I woulda thought the filter would have caught it all
_________________ ED Fairmont, Ghia mock DOHC-T 11.6 @ 118 Trying to get back to the 1/4! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 42 guests |
