|
| Grumpyoldman |
|
||
|
Hi All just looking to buy a New Cat for my Au Falcon, My local Exhaust centre wants $330 for a high flow cat that they couldnt give me the name of and i have been looking at the ones off Ebay like the 2.5" High Flow Cat BOKKA Metal Falcon AU-BA XR6/XR8/GT
100 cpsi Euro III Emission Standard - 5 Year Warranty or 1x Kenobi HF100 2.5" Metal-Core Catalytic Converter (100 CPSI) Im have a set of Pacey 4480 to go on at the same time aswell as a 2.5" Cat back Exhaust System. My main worry is are these Cats legal for NSW please or are they not. Many thanks Grumpy |
||
| Top | |
||
| DARTHVADER |
|
|||
|
hi mate.
I dont think that a metal cat is going to be very legal at all. but i could be wrong. Try one of sponsers on this site. VENOM. those fellas will set you on the right track here tis www.venomexhaustworks.com.au MITCHY
_________________ AUIII, PACEY 4499's, MAGNIFLOW CAT, 2.5" ZORST, 17X8" AUII XR RIMS....otherwise all factory! |
|||
| Top | |
|||
| bry40l |
|
|||
|
Grumpyoldman wrote: Hi All just looking to buy a New Cat for my Au Falcon, My local Exhaust centre wants $330 for a high flow cat that they couldnt give me the name of and i have been looking at the ones off Ebay like the 2.5" High Flow Cat BOKKA Metal Falcon AU-BA XR6/XR8/GT 100 cpsi Euro III Emission Standard - 5 Year Warranty or 1x Kenobi HF100 2.5" Metal-Core Catalytic Converter (100 CPSI) Im have a set of Pacey 4480 to go on at the same time aswell as a 2.5" Cat back Exhaust System. My main worry is are these Cats legal for NSW please or are they not. Many thanks Grumpy post up the links to these cats, im sure if they are any good at all some one on this forum has used them or knows some one who has at some point
_________________ BF XR6 |
|||
| Top | |
|||
| SWC |
|
||
|
Just grab a Dunnydoor V8 Cat, they are already flanged and are 2.5" and they go cheap.
|
||
| Top | |
||
| bry40l |
|
|||
|
SWC wrote: Just grab a Dunnydoor V8 Cat, they are already flanged and are 2.5" and they go cheap. Do they fit straight into a falcon like the original one?
_________________ BF XR6 |
|||
| Top | |
|||
| Grumpyoldman |
|
||
|
These are the links to what i was looking at on ebay and No i dont think it can go Straight in as i have a set of 4480 Pacemaker to install aswell so it wont be at the same angle.
http://www.ebay.com.au/itm/2-5-High-Flo ... 4cf429123d http://www.ebay.com.au/itm/2-5-High-Flo ... 2eaec5e7c4 http://www.ebay.com.au/itm/High-Flow-2- ... 3a64424f6e |
||
| Top | |
||
| fairlane6970 |
|
|||
|
I bought two of those 2.5 in. Bokka ones for my 5.0 NF when I did the exhaust, they seem fine, I was told by another member that they looked identical to the Venom ones he had just bought at half the price of the venoms.
_________________
|
|||
| Top | |
|||
| SWC |
|
||
|
Have one here, I will check tomorrow against exrtractors, but I think they do.
|
||
| Top | |
||
| Papa Smurf |
|
||
|
The original Catalytic convertors were AC Delco manufacture a division of General Motors.
I recently received advice from a Sponsor of this site who is involved with tuning and other performance goodies, he advised me to get a Magna-flow Metal one for my AU XR6 and the cheapest I have seen so far is $245.00 online and of course you will need 4 flanges to have it fitted to your car. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 76 guests |
