-95 octane (ethanol blend): This particular fuel contains a 20% blend of a substance known as ethanol, which is not all that it is made out to be. Ethanol is only good for cars that are designed to run off it. Ethanol will cause damage to 98% of cars as they are simply not designed to run off ethanol fuel. You do not get the same mileage for the same dollar value of your recommended fuel, besides being cheaper;
95 octane fuel- Ethanol ($1.25 per Litre) Buys you 16 Litres Taking you 120 kilometres.

The Society of Automotive Engineers, usually abbreviated as SAE, has established a numerical code system for grading motor oils according to their kinematic viscosity. SAE viscosity gradings include the following: 0, 5, 10, 15, 20, 25, 30, 40, 50 or 60. Some of the numbers can be suffixed with the letter W, designating their "winter" or cold-start viscocity, at lower temperature.
Viscocity is graded by measuring the time it takes for a standard amount of oil to flow through a standard orifice, at standard temperature. The longer it takes, the higher the viscocity, and thus higher SAE code.

Note that the SAE operate a separate viscosity rating system for transmission oils which should not be confused with engine oil viscosity. The higher numbers of a transmission oil (eg 75W-140) do not mean that it is necessarily higher viscosity than an engine oil


The temperature range the oil is exposed to in most vehicles can be wide, ranging from cold ambient temperatures in the winter before the vehicle is started up to hot operating temperatures when the vehicle is fully warmed up in hot summer weather. A specific oil will have high viscosity when cold and a low viscosity at the engine's operating temperature. The difference in viscosities for any single-grade oil is too large between the extremes of temperature. To bring the difference in viscosities closer together, special polymer additives called viscosity index improvers, or VIs are added to the oil. These additives make the oil a multi-grade motor oil. The idea is to cause the multi-grade oil to have the viscosity of the base number when cold and the viscosity of second number when hot. This enables one type of oil to be generally used all year, and when multi-grades were initially developed, they were frequently described as all-season oil. The viscosity of a multi-grade oil still varies logarithmically with temperature, but the slope representing the change is lessened. This slope representing the change with temperature depends on the nature and amount of the additives to the base oil.

The SAE designation for multi-grade oils includes two grade numbers; for example, 10W-30 designates a common multi-grade oil. Historically, the first number associated with the W (again 'W' is for Winter, not Weight) is not rated at any single temperature. The "10W" means that this oil can be pumped by your engine as well as a single-grade SAE 10 oil can be pumped. "5W" can be pumped at a lower temperature than "10W" and "0W" can be pumped at a lower temperature than "5W". The second number, 30, means that the viscosity of this multi-grade oil at 100°C (212°F) operating temperature corresponds to the viscosity of a single-grade 30 oil at same temperature. The governing SAE standard is called SAE J300. This "classic" method of defining the "W" rating has since been replaced with a more technical test where a "cold crank simulator" is used at increasingly lowered temps. A 0W oil is tested at -35°C, a 5W at -30°C and a 10W is tested at -25°C. The real-world ability of an oil to crank in the cold is diminished soon after put into service. The motor oil grade and viscosity to be used in a given vehicle is specified by the manufacturer of the vehicle (although some modern European cars now make no viscosity requirement), but can vary from country to country when climatic or mpg constraints come into play. Oil circulates through the piston oil rings to cool and lubricate the compression rings. Inside gasoline engines, the top compression ring is exposed to temperatures as high as 320 °F (160 °C).

Many new vehicles are marked to use 5W-20 oil (Honda, Ford, and more recently Toyota) which is not much thinner than a 30W oil. Nay-sayers of 20W oil's ability to protect engines should note that typically, 30W oils shear down into the 20W range anyway. Most engine wear is during start-up and warm-up period, where the thinner 20W oil's flow is desirable. Overall, lab test results of the wear metals contained in used oil samples show low or lower wear with 20W than 30 in applications it is specified for. Some ultra fuel efficient and hybrid vehicles are marked to use 0W-20 oil. For some selective mechanical problems with engines, using a more viscous oil can ameliorate the symptoms, i.e. changing from 5W-20 to 20W-50 may eliminate a knocking noise from the engine but doesn't solve the problem, just "masks" it. Excess amounts of oil consumed by an engine burning it can be addressed by using a thicker oil, a 10W-40 might not burn off as fast compared to a 5W-30. A newer product that also addresses this issue is the "High-Miles" oils now marketed. They tend to be slightly thick for their grades, contain extra additives and seal conditioners. Apparently the formulation of these oils works well in many instances.