|
| mikey6cyl |
|
||
|
I blew a heater hose and dropped all my coolant. engine stopped on its own have replaced hose and coolant but engine wont kick over. is turning over but not firing.
|
||
| Top | |
||
| Falcon96XR6 |
|
|||
|
Has it got spark? Id check that first it could have killed your coil or dizzy from getting so hot.
Checked it for codes?
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| roughredXR6 |
|
|||
|
Stopped on its own? That's bad.
Did it stop as soon as the hose blew out, or did it stop because you kept driving after it blew? I hope you didn't put cold water into it while it was red hot.....
_________________ Ported ED XR6 head shaved too much, AU gasket, custom Crow Cam, Pacemaker 4480's, 5-speed conversion, billet aluminium flywheel, GT clutch, T.I. Performance J3 chip, custom water/methanol injection, modified BA throttle body. Paint&Panel by Barbed Wire Fence. |
|||
| Top | |
|||
| mikey6cyl |
|
||
|
it was I idling when it stopped to see where water was coming from didnt refill til next day.
|
||
| Top | |
||
| roughredXR6 |
|
|||
|
Then yeah, like '96XR6 said, check for spark. Probably hosed the coil and dizzy.
_________________ Ported ED XR6 head shaved too much, AU gasket, custom Crow Cam, Pacemaker 4480's, 5-speed conversion, billet aluminium flywheel, GT clutch, T.I. Performance J3 chip, custom water/methanol injection, modified BA throttle body. Paint&Panel by Barbed Wire Fence. |
|||
| Top | |
|||
| mikey6cyl |
|
||
|
codes?
|
||
| Top | |
||
| roughredXR6 |
|
|||
|
He means ecu fault codes.
Check for spark first.
_________________ Ported ED XR6 head shaved too much, AU gasket, custom Crow Cam, Pacemaker 4480's, 5-speed conversion, billet aluminium flywheel, GT clutch, T.I. Performance J3 chip, custom water/methanol injection, modified BA throttle body. Paint&Panel by Barbed Wire Fence. |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
Was it one of the hoses that go into the fire wall? If so then id say its sprayed your dizzy and coil as 'roughredXR6 said,
Or as i said heat has possibly hurt your coil, as it sits on the block right near 5&6cyl.. check for spark, if you have spark, check ecu fault codes.
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| mikey6cyl |
|
||
|
can I replace dissy from underneath or will I need to take intake off as its under
|
||
| Top | |
||
| roughredXR6 |
|
|||
|
You can get it out with manifold in place, but it's a mission.
Would be surprised if it's dead though, just make sure it's dry inside. More likely to be coil if no spark.
_________________ Ported ED XR6 head shaved too much, AU gasket, custom Crow Cam, Pacemaker 4480's, 5-speed conversion, billet aluminium flywheel, GT clutch, T.I. Performance J3 chip, custom water/methanol injection, modified BA throttle body. Paint&Panel by Barbed Wire Fence. |
|||
| Top | |
|||
| mikey6cyl |
|
||
|
cheers! il check after work. watch this space
|
||
| Top | |
||
| roughredXR6 |
|
|||
|
No worries mate. Let us know how you go.
_________________ Ported ED XR6 head shaved too much, AU gasket, custom Crow Cam, Pacemaker 4480's, 5-speed conversion, billet aluminium flywheel, GT clutch, T.I. Performance J3 chip, custom water/methanol injection, modified BA throttle body. Paint&Panel by Barbed Wire Fence. |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
Yes. Please do, good luck.
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| mikey6cyl |
|
||
|
sooooo I have spark. its orange and weak though.
|
||
| Top | |
||
| mikey6cyl |
|
||
|
whats the best way to clean fuel pump and line?
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 69 guests |
