|
| bry40l |
|
|||
|
it would be good to have the knock sensor wired up, but its not really needed is it?
_________________ BF XR6 |
|||
| Top | |
|||
| TROYMAN |
|
||
|
bry40l wrote: it would be good to have the knock sensor wired up, but its not really needed is it? not really, i had it connected when i did my ea but didnt bother connecting it with the ed |
||
| Top | |
||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
Can you tell me the what pin goes in what hole....
I have a spare eb loom here to salvage pins And how do you mean water temp depending on what? My eb has 3 sensors on the thermostat housing what are they all for? I plan to wire the knock sensor |
||
| Top | |
||
| TROYMAN |
|
||
|
you just use the eb lower thermostat housing in the ef engine, the ef has the one sensor for water temp that is sent to the ecu and temp gauge..
eb has the one for the ecu, one for the temp gauge and depending on wether your eb is a fairmont or gl the 3rd one is either for climate control in fairmont or if it has hoses on it its for the ac vent control in series1... |
||
| Top | |
||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
What does the el computer do with temp inputs..?
How many Does it have as i will be wiring to suite el computer not the eb |
||
| Top | |
||
| TROYMAN |
|
||
|
the el ecu needs the water temp for cold start, it needs the information so the ecu can adjust fuel and timing to suit the water temp..
if you use the eb sensors with the eb wiring it will work fine as the large sensor is the same from both.. the eb just needs the extra small sensor for the gauge on the dash... |
||
| Top | |
||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
is there a trick to removing the cam angle sensor from the ef engine?
|
||
| Top | |
||
| Troy |
|
||
|
should come straight out
|
||
| Top | |
||
| bry40l |
|
|||
|
theres a retaining bolt and bracket, once thats removed it should pop straight out as troy stated
_________________ BF XR6 |
|||
| Top | |
|||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
thats what i thought .."just like a dizzy".... ill have another look cheers guys!!
|
||
| Top | |
||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
what is the sensor on the back of both intake manifolds used for?
with the altered loom back on the motor i realized this plug is too short.? |
||
| Top | |
||
| razza01 |
|
||
|
I think thats the air charge temperature sensor.
|
||
| Top | |
||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
Thank you.... I extended the wire and replaced the plug...
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 35 guests |
