|
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
Can i use an ef xr ecu on my ef xr motor in my eb with eb dissy & coil ...
Or will the computer not run the dizzy ect .. i am using all the ef accesorys I plan to modify my eb engine loom to suite the ef motor Thanks |
||
| Top | |
||
| TROYMAN |
|
||
|
no , not unless you use the whole ef wireing loom and coil packs as ef ecu has 104 pins and eb ecu has 60 pins..
but you can use a el ecu with the eb loom as el has a dizzy set up and the ecu has 60 pins like eb |
||
| Top | |
||
| bry40l |
|
|||
|
you will need an eb,ed or el ecu, the ef one is for the coilpack only
_________________ BF XR6 |
|||
| Top | |
|||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
So its either a full ef loom or find a eb-el xr ecu ?
Will the xr engine run on a falcon ecu? |
||
| Top | |
||
| TROYMAN |
|
||
|
tickford861 wrote: So its either a full ef loom or find a eb-el xr ecu ? Will the xr engine run on a falcon ecu? yes and yes |
||
| Top | |
||
| bry40l |
|
|||
|
yep will run fine on a standard falcon one, are you running the ef inlet manifold or the eb?
_________________ BF XR6 |
|||
| Top | |
|||
| Troy |
|
||
|
yea use the el ecu, yes the falcon ecu will work.
what inlet manifold will you be using? |
||
| Top | |
||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
I was planning on using the ef bbm ..if im not going to be able to run the ef ecu there will be no trigger for bbm and thermos.... what do i do about that ???? Cheerz
|
||
| Top | |
||
| bry40l |
|
|||
|
tickford861 wrote: I was planning on using the ef bbm ..if im not going to be able to run the ef ecu there will be no trigger for bbm and thermos.... what do i do about that ???? Cheerz run the el ecu as it can run the thermos and bbm
_________________ BF XR6 |
|||
| Top | |
|||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
And an el ecu will plug into my loom?
|
||
| Top | |
||
| bry40l |
|
|||
|
yes sir it will
_________________ BF XR6 |
|||
| Top | |
|||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
For my engine loom it looks like i will have to extend the throttle body wires .. chnge the plug on the top of the throttle body is that all.. ...also on my eb thermostat housing i have three sensors on the ef i have one...what is the other two used for.. thankyou
|
||
| Top | |
||
| tickford861 |
|
||
Age: 33 Posts: 76 Joined: 19th Mar 2012 Ride: EB Fairmont Ghia Location: Radelaide , South Australia |
When i get an el ecu will i need to add pins and wires to the loom
|
||
| Top | |
||
| the sam |
|
||
|
Depends.
You will need to for some things: -bbm -thermos -knock sensor -coolant sensor (depending) The Troydude is probably the best with this seeing as he has done it. Or did you use a whole loom Troy?
_________________ LOW, LOUD AND LUMPY |
||
| Top | |
||
| TROYMAN |
|
||
|
no, in my case i used the ed loom and extended the tps and isc wires to the throttle body, added a couple of wires to the ecu plug for the bbm solinoid and knock sensor and ran them through to the engine bay..
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 25 guests |
