|
| madeaspack |
|
||
|
can i and should i use an au rebuild kit??
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| stockstandard |
|
|||
|
not unless you have a hybrid engine.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| madeaspack |
|
||
|
its not hybrid,so el should be good,not au pistons or anything?
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| stockstandard |
|
|||
|
If you go au pistons you need au rods
the main bearings on the AU are a different size as well
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| grumblebum04 |
|
||
|
Whats the build date and have you got an alloy (cast) sump or steel one?
Also read the sticky's on different engines at start of this forum.
_________________ The thunder of .05 will echoe around Bathurst for ever. |
||
| Top | |
||
| cjh |
|
|||
|
I thought you could use AU pistons in an EL engine, as long as the gudgeon pin sizes are the same, deck heights are the same.?????
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| stockstandard |
|
|||
|
cjh wrote: I thought you could use AU pistons in an EL engine, as long as the gudgeon pin sizes are the same, deck heights are the same.?????
pin size is the same, deck height is the same, but rod length/pin height is different. AU pistons will sit .120" lower in the bores on EL rods.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| cjh |
|
|||
|
I meant deck height of the pistons, pin to top of piston distance......are they the same????
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| stockstandard |
|
|||
|
nope
E-series use a 5.88" rod, AU onwards use a 6" rod with higher pins.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| cjh |
|
|||
|
stockstandard wrote: nope
E-series use a 5.88" rod, AU onwards use a 6" rod with higher pins. Stockstandard.............What is the crankpin journal size on an AU ???
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| cjh |
|
||||||
|
I now have the correct rods for the pistons I'm using. They are AUII rods, brand new, and have cleaned them up a bit.
_________________ http://youtu.be/jJTh9F3Vgg0 |
||||||
| Top | |
||||||
| Who is online |
|---|
Users browsing this forum: Google [Bot], Google Adsense [Bot], willams and 135 guests |
