|
| TROYMAN |
|
||
|
g day
had the manifold and injectors been sitting around for a while before you put the engine in?? when i did mine the manifold had been sitting around for a while and one injector had blocked up with dry petrol residue.. and mine would only run on 5 cyl and would pop out the exhaust and idled really rough.. so i fitted the injectors from my log manifold and it come good... |
||
| Top | |
||
| P100 Ute |
|
|||
|
i got spare injectors here off a mpfi manifold that i bought ages ago.
electrishians havent started work on my car yet. but they say it'll be finished by 4.30pm so afterwards maybe sort something out im stuck @ my parents house waiting and the injectors are @ my house in willagee..
_________________
|
|||
| Top | |
|||
| ToxicBFturbo06 |
|
||
|
i guess it's your map sensor onthe fire wall what it does is dump lots of fuel in the intake. if the map vac is of it thinks there is a lot of air in the intake. use the el map sensor.
_________________ my new Bf XR6 Turbo it's the lion eater. |
||
| Top | |
||
| HaZZa |
|
|||
|
ive got the injectors on the log manifold of the eb might try swapping them over and see whats up prob wont be able to do it till later tonight as i have my work post xmas party tonight in morley. ill have aplay around now but wont have much time. will have to have a good look at it later tonight or tomorow.
|
|||
| Top | |
|||
| HaZZa |
|
|||
|
well just replaced the injectors with the ones off the eb log manifold . and its still doing the same thing.
my heads hurting from the smeel of fuel so i think ill have to give it a miss for today and start fresh tomoro. ne other surgestions owuld be great . cheer's ppl |
|||
| Top | |
|||
| HaZZa |
|
|||
|
well just replaced the injectors with the ones off the eb log manifold . and its still doing the same thing.
my heads hurting from the smeel of fuel so i think ill have to give it a miss for today and start fresh tomoro. ne other surgestions owuld be great . cheer's ppl |
|||
| Top | |
|||
| Southy |
|
|||
|
Well have you tried putting the EL ECU in yet?
|
|||
| Top | |
|||
| HaZZa |
|
|||
|
well just talked to a mate (mungrel eb ) some might know of him.
he was saying it would be the fuel pump. the eb fule pulmp run a higher pressure or something and that i should swap it for a el 1. coz it would be running to high of a pressure in the rail. dont know if its right or not. but hes bring one around on the week end to c. if not hopefully be able to give me a hand to sort it out. he has done a fair amount of conversions including el int xf and a whole heap of s**t. hopefully be able to work it out. will keep u all posted on how it turns out. |
|||
| Top | |
|||
| HaZZa |
|
|||
|
yeh its in
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
do you have the vaccum line conected to the fuel regulator.?????
|
||
| Top | |
||
| snap0964 |
|
|||
|
Did you fit the injector electrical plugs back onto the correct injectors?? - they fire in banks of 3: 1,3,5 & 2,4,6.
Easiest way to check out individual injectors is the pull the respective electrical plug while the engine is running - engine runs rougher is okay, no change, injector is clogged or no power to it.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| HaZZa |
|
|||
|
yep vacum hose conected to regulator and wires all hooked up to correct injector .
|
|||
| Top | |
|||
| HaZZa |
|
|||
|
hey guys . well been trying to get it working again today and nothing better.
still poping and f@rt. im really htinking it may be the timing. how do, can i make sure its a tdc on the compresion stroke? i tryed taking the #1 plug out and feeling for sucking or pressure but i cant feel nething. (while hand cranking the motor.) its got me thinking. how would a motor run if the timing was set to tdc but not on the compression stroke? and what positon r the other cylnders when on tdc? by memory 1 and 6 was at tdc and the other 4 were pretty well even (half to 3/4 way down the bore? ) is this right ? or have i got it wrong? (knowing me ive stuffed up ) all the other timing marks are aligned. and the dizzy is at the finish mark when at tdc |
|||
| Top | |
|||
| EL__Fairmont |
|
|||
|
HaZZa wrote: hey guys . well been trying to get it working again today and nothing better.
still poping and f@rt. im really htinking it may be the timing. how do, can i make sure its a tdc on the compresion stroke? i tryed taking the #1 plug out and feeling for sucking or pressure but i cant feel nething. (while hand cranking the motor.) its got me thinking. how would a motor run if the timing was set to tdc but not on the compression stroke? and what positon r the other cylnders when on tdc? by memory 1 and 6 was at tdc and the other 4 were pretty well even (half to 3/4 way down the bore? ) is this right ? or have i got it wrong? (knowing me ive stuffed up ) all the other timing marks are aligned. and the dizzy is at the finish mark when at tdc it sounds like what happened after converting my OLD EB cpi to multipoint. I started it and it would just run f@rt and popping. I checked the timing( had to run it at wot just to keep it running). Was running retarded, could barely pick up the mark with the timing light, was right down low. I then removed the dizzy and dropped it in on the next cog on the gear. There are two positions that the mpi dizzy will drop in and both seem right , but only 1 will get have the correct timing. Started the car and it idled perfect. cheers.
_________________ 97 EL Fairmont 4l OHC .Silver. |
|||
| Top | |
|||
| HaZZa |
|
|||
|
well played around with the timing today and still nothing . think she's a bit flooded . even befor i redid the timing. she wouldnt start. then re did the timing and still wont start. got a make dropping by soon to have a look see hopefull be able to sus out the prob.
well thats it for now. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 122 guests |
