|
| DaPlaya |
|
||||
|
Hi Guys,
I've been told that engine mounts in my ELXR6 will probably need replacing (car has done 217k). I have the round hydraulic type mounts, as apposed to the square solid rubber mounts. I've had a look and they don't appear to be perished both look exactly the same, I don't feel any extra vibration when at idle, no engine slap when changing gear etc. I took a photo of the mount that is under the intake manifold, I notice both have a rubber ring on the bottom that is detached and spins freely is this normal? Can anyone else post a pic of a new mount from EL that I can compare or even on car?
|
||||
| Top | |
||||
| ef_falcon_95 |
|
|||
|
What if it's manual ?
_________________ El XR6 Turbo |
|||
| Top | |
|||
| DaPlaya |
|
||
|
ef_falcon_95 wrote: What if it's manual ? Which it is. I'm guessing just ride the clutch with handbrake on |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
My handl brake won't hold , I sometimes get slight vibration at low revs , could be engine mounts ?
_________________ El XR6 Turbo |
|||
| Top | |
|||
| DaPlaya |
|
||
|
ef_falcon_95 wrote: My handl brake won't hold , I sometimes get slight vibration at low revs , could be engine mounts ? Adjust your hand brake so it works adequately. Is your vibration coming when driving or just sitting there idling, or in neutral slowly revving? |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
When I come to a stop at traffic lights the exhaust vibrates on the body , it's only a slight vibration . I had the exhaust modified to clear the body but still rattles the slightest bit .
When I give it a rev it goes away
_________________ El XR6 Turbo |
|||
| Top | |
|||
| SWC |
|
||
|
DaPlaya wrote: Hi Guys, I've been told that engine mounts in my ELXR6 will probably need replacing (car has done 217k). I have the round hydraulic type mounts, as apposed to the square solid rubber mounts. I've had a look and they don't appear to be perished both look exactly the same, I don't feel any extra vibration when at idle, no engine slap when changing gear etc. I took a photo of the mount that is under the intake manifold, I notice both have a rubber ring on the bottom that is detached and spins freely is this normal? Can anyone else post a pic of a new mount from EL that I can compare or even on car? The Photo that you have posted up show a good Mount. When they go they collapse and sink down and rest metal on metal. Passenger side is usually ok, what doe the drivers side look like. This is the side that usually gives out due the heat from the exhaust. |
||
| Top | |
||
| DaPlaya |
|
||
|
Thanks mate, I'll take a photo of the other and post it up then let me know what you think. Cheers
|
||
| Top | |
||
| DRHEMI |
|
|||
|
I got new mounts in my EF back in August 2009
These were repo ones not Ford ones - they do the job  Close Ups  
_________________ PROEF 13.46 @ 105.78mph - 1994 Ford Fairmont EF NA 6cyl Man 3.9 diff Sedan |
|||
| Top | |
|||
| DaPlaya |
|
||
|
DRHEMI wrote: I got new mounts in my EF back in August 2009 These were repo ones not Ford ones - they do the job Close Ups Thanks for the post matey, however they're the square solid rubber angle mounts, I have the round hydraulic style which are straight up and down. mind you by the looks of that all I would need is a bracket to make those angles fit |
||
| Top | |
||
| DRHEMI |
|
|||
|
I am petty sure i had the round ones before and these were the replacements
I will see if i can find a pic which confirms it is that the round mount in this pic? bottom - middle? 
_________________ PROEF 13.46 @ 105.78mph - 1994 Ford Fairmont EF NA 6cyl Man 3.9 diff Sedan Last edited by DRHEMI on Tue Feb 28, 2012 9:31 pm, edited 2 times in total. |
|||
| Top | |
|||
| DaPlaya |
|
||
|
Did they come with those brackets (brass coloured)?
|
||
| Top | |
||
| DaPlaya |
|
||
|
DRHEMI wrote: I am petty sure i had the round ones before and these were the replacements I will see if i can find a pic which confirms it is that the round mount in this pic? bottom - middle? Yep they are the round ones. What make/model are your headers? |
||
| Top | |
||
| DRHEMI |
|
|||
|
DaPlaya wrote: What make/model are your headers? Pacemaker 4480 HPC Ceramic Coated DaPlaya wrote: Did they come with those brackets (brass coloured)? Yeah the did Here is an earlier pic - you can see the old ones here that were replaced - I played with the Pic so you can see them better thats what its so crap lol If you still can't see them then save the pic to your computer and make the pic brighter 
_________________ PROEF 13.46 @ 105.78mph - 1994 Ford Fairmont EF NA 6cyl Man 3.9 diff Sedan |
|||
| Top | |
|||
| EL___Fairmont |
|
|||
|
DaPlaya wrote: Hi Guys, I've been told that engine mounts in my ELXR6 will probably need replacing (car has done 217k). I have the round hydraulic type mounts, as apposed to the square solid rubber mounts. I've had a look and they don't appear to be perished both look exactly the same, I don't feel any extra vibration when at idle, no engine slap when changing gear etc. I took a photo of the mount that is under the intake manifold, I notice both have a rubber ring on the bottom that is detached and spins freely is this normal? Can anyone else post a pic of a new mount from EL that I can compare or even on car? The passenger side one is always good, check the driver's side one too see if it's metal on metal or resting on that rubber seperation pad. I paid about $120 for these square type ones as mentioned above, which were fitted too lates series 2 Hybrid 98 model EL Falcons. These can handle the heat from pacemaker extractors.. Kelpro part # (mount) MT8370, (bracket) MTB8370
_________________ Current ride 2007 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google [Bot] and 38 guests |
