|
| FastFutura |
|
|||
|
anyone replaced engine mounts?
i wanna replace the one on the extractor side, cos my whole box is shakin (esp at lumpy idle) and i reckon it migh dial out some backlash from the driveline... how much should they be, are there any nolathane ones available, and can i jsut sorta hoist the engine a bit and chock it while i replace it.. are the other ones easy to get at and change, or do i gotta pull engine out.
_________________ 94 ED Futura, 5spd, RPM clutch,3.27 LSD, PH4480 pacemakers, 2.5'' Supercat, STG 2 Wade1004-112 advanced16degrees, XH intake K&N panel,pedders superlows, Expursuit puter. clearindicators, volvoTT thermofan
|
|||
| Top | |
|||
| Disco Frank |
|
|||
|
get the EF/EL ones i cant rember which ones scott said to use
but they are about $250 for teh pair and are real real good
_________________ RIP SCOTT |
|||
| Top | |
|||
| loxxr6 |
|
|||
|
This may be something I may need to have replaced.
How difficult are they to change ? |
|||
| Top | |
|||
| uglybob |
|
|||
|
Disco Frank wrote: get the EF/EL ones i cant rember which ones scott said to use
but they are about $250 for teh pair and are real real good 99% sure its the EL ones which are the better of the 2 frank... 
_________________ R.I.P. Scotty |
|||
| Top | |
|||
| altedxr6 |
|
|||
|
I've replaced many engine mounts, yes you can get nolathane, (i can supply them)
You don't need a engine host, but it helps  or use a trolley jack and some wood ... Im pretty sure the EF/EL ones don't fit onto a EA-ED mount .because when I was putting the EF motor into my ED I had to use the ED engine mounts.
|
|||
| Top | |
|||
| nannas_ed |
|
|||
|
loxxr6 wrote: This may be something I may need to have replaced.
How difficult are they to change ? not a huge drama, just: place a trolley jack under the engine, jack it up so its releiving some of the pressure of the eng mount then undo the eng mount bolts. you might have to do these with a rattle gun or a real big breaker bar. then when thats done jack the moter up and take the mount of and replace it. its ok to jack the engine from the sump coz your not jacking the whole car up. you have to jack it up just enough to get the old mount out and the new one in.
_________________
|
|||
| Top | |
|||
| DrE |
|
|||
|
ive been through 6 engine mounts on the exhaust side and the current one has started seperating already
 what would cause that
_________________
|
|||
| Top | |
|||
| nannas_ed |
|
|||
|
DrE wrote: ive been through 6 engine mounts on the exhaust side and the current one has started seperating already
what would cause thats**t, mine have been on there since the car rolled out the showroom and they still look brand new. something wrong there. is oil being dripped onto them?????
_________________
|
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
dre maybe it's that spolier
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| altedxr6 |
|
|||
|
EDMONTY wrote: dre maybe it's that spolier
yeah, i've been trying to get him to take it off! lol |
|||
| Top | |
|||
| Disco Frank |
|
|||
|
DrE wrote: ive been through 6 engine mounts on the exhaust side and the current one has started seperating already
what would cause thatumm get rid of the spiler for starters! how close it the exhaust to the mount? have u replced th other side? if the intake side is fooked then the new exhaust side will go quick smart
_________________ RIP SCOTT |
|||
| Top | |
|||
| DrE |
|
|||
|
sorry wasnt thinking straight when i posted that b4 its the intake side that keeps breaking exhaust side is fine, no oil dripping onto it i dont even dump the clutch very often so it doesnt cop to much of a hiding, im sick of them breaking thinking of just welding it lol
_________________
|
|||
| Top | |
|||
| Disco Frank |
|
|||
|
replace BOTH at the same time and go from there
dont weld it LOL will get real bade vibrations through the car do u rev the car alot?
_________________ RIP SCOTT |
|||
| Top | |
|||
| DrE |
|
|||
|
not really, ill go some brand newwy nolathane ones and see how long they last do them at the same time and see how i go
_________________
|
|||
| Top | |
|||
| FastFutura |
|
|||
|
au2low wrote: I've replaced many engine mounts, yes you can get nolathane, (i can supply them)
You don't need a engine host, but it helps or use a trolley jack and some wood ... Im pretty sure the EF/EL ones don't fit onto a EA-ED mount .because when I was putting the EF motor into my ED I had to use the ED engine mounts.wicked, they sound good, how much could i get them for? im in perth? cos i reckon ill do em pretty soon, try get rid of some more backlash, uni joints will be next.
_________________ 94 ED Futura, 5spd, RPM clutch,3.27 LSD, PH4480 pacemakers, 2.5'' Supercat, STG 2 Wade1004-112 advanced16degrees, XH intake K&N panel,pedders superlows, Expursuit puter. clearindicators, volvoTT thermofan
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 49 guests |
