|
| claytonxr6 |
|
|||
|
Im looking at getting some Pacemaker headers for my XH XR6 ute, Ive already got a custom made 2.5" exhaust - my question is will I need a high flow cat or will the stock one be enough (havent had any dramas with it so far). Have had mixed opinions on this so far, any ideas?
_________________ See Ya on the road Scag...see ya on the road. |
|||
| Top | |
|||
| tomcolahan |
|
|||
|
If the standard cat is still in good condition it will be fine. You will probably need to get the outstide casing taken off it, and the lead in pipe chopped down a bit though, and new flanges welded on..
_________________ We'll keep our cow s**t in the country, you keep your bull s**t in the city. |
|||
| Top | |
|||
| hornet |
|
|||
|
When I got my PH4480's fitted, they kept my cat as it was in good condition. For the sake of $350, I don't think its holding back much power.
_________________ 5 Speed EL Futura
|
|||
| Top | |
|||
| Shum's EL |
|
|||
|
yeah just stick with the stockie...
|
|||
| Top | |
|||
| smoke_ |
|
|||
|
i replaced mine when i got a system, 11 year old on the original cat.
it had only 125,000km on it, but $880 for 4480's, and a full 2.5in system with hi-flow cat, i wasn't gonna say no.
_________________ NEW RIDE - FPV FG F6 6spd Auto. 12.26@114MPH, 1.88 60FT on Cheapy Tyres with 38PSI - Stock except K&N filter! |
|||
| Top | |
|||
| Sierra |
|
|||
|
Just out of curiosity .... what is the internal diameter of a standard cat?
is it narrower than the id of a 2.5" system?
_________________ 95 EF XR6 Manual |
|||
| Top | |
|||
| twr7cx |
|
|||
|
Sierra wrote: Just out of curiosity .... what is the internal diameter of a standard cat?
is it narrower than the id of a 2.5" system? cats arn't like mufflers were they have the pip[e running through them. the flow through a cat is like hitting a brick wall with big holes in it. |
|||
| Top | |
|||
| Sierra |
|
|||
|
twr7cx wrote: Sierra wrote: Just out of curiosity .... what is the internal diameter of a standard cat? is it narrower than the id of a 2.5" system? cats arn't like mufflers were they have the pip[e running through them. the flow through a cat is like hitting a brick wall with big holes in it. Thanks twr7cx .... I did actually forget about that fact .... 
but it would still it would have a certain inlet and outlet diameter
_________________ 95 EF XR6 Manual |
|||
| Top | |
|||
| Mechan1k |
|
||
|
The standard cat inlet outlet looks to be 2" ... maybe 2.25" ... I had a look at mine the other day.
It's slowly gutting itself ... bits are tinkling in the exhaust and I get mad vibration sounds from it as well ... when i get the extractors I'll replace the cat at the same time.
_________________ 04 Territory TX AWD - Winter White - optioned up |
||
| Top | |
||
| claytonxr6 |
|
|||
|
cheers fellas, going to stick with the one Ive already got on there for a bit longer.
_________________ See Ya on the road Scag...see ya on the road. |
|||
| Top | |
|||
| mreb |
|
|||
|
yeh the outlet on the cat is smaller that the inlet ,had my exhaust done 21/2 inch and the exhaust shop chopped the pipe off the back off the cat and welded in the bigger one 21/2 pipe
|
|||
| Top | |
|||
| Grumblexr6 |
|
||
|
I got the same thing XH XR, what would a set on Extractors cost me and a High Flow Cat would anyone know Thanx
|
||
| Top | |
||
| BNKRBR |
|
||
|
man whats the point off all that money spent on a exhaust if u have a cat that is smaller then the diamiter of the exhaust.
seriously man get your self a 3 inch hi flow cat of ebay, i just got one for 135 bucks. the bigger diamiter pipe the better the flow and the more exhaust gas the cat can take on and flow through faster. if u use your standard cat then you would have wasted your money on the extractors and exhuast. i know this will make some people touchy but its a fact look it up on autospeed site. general rule if you have a 2.5 inch exhaust sytem then get a 3 inch cat. |
||
| Top | |
||
| Waggin |
|
|||
|
I ran the factory cat on my waggin and got 183RWKW N/A. If the cat is in good condition, just get it flanged to suit your 2.5" system. These 3" "hi-flow" cats are rubbish.. the cross section isn't as wide as the factory cat, and they infact flow less. There's more to a cat than its flange ID.
_________________ WAG363: AUII LTD Supercharged 363 Dart Stroker [Supercharged 363 LTD Build] |
|||
| Top | |
|||
| BNKRBR |
|
||
|
well id like to see flow tests on hi flow cats and flow tests on standard cats , im sure hi flow cats wouldnt be so recomemded if they dint do anything.
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 84 guests |
12.06@120MPH
