|
| clampy |
|
||
|
i had extractors and a high flow cat fitted last friday and yester i notice loss or power and a funny noise from the exhaust under the bonnet.... any way opened the bonnet and the flanges between the cat and extractors where the sensor is the gasket was hanging out and can feel pressure coming out of it, this ever happened to any one before????
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| phongus |
|
|||
|
clampy wrote: i had extractors and a high flow cat fitted last friday and yester i notice loss or power and a funny noise from the exhaust under the bonnet.... any way opened the bonnet and the flanges between the cat and extractors where the sensor is the gasket was hanging out and can feel pressure coming out of it, this ever happened to any one before???? Sounds like a dodgy job, hasn't happened before and I believe you should take it back to the fitter and tell them to fix it. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| clampy |
|
||
|
yeah thats the plan on monday..... dodgy s**t
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| OZBMX |
|
|||
|
Obviously they didn't tightenthe bolts up enough, I made that mistake when I fitted mine, long story short jump under either look for a replacement bolt temporarily lift the gasket up tighten both bolts up, don't stress to much though, and then book it in asap, it depends how long it's been like that but you may need to replace the gasket, so I'd be getting them to change it anyway.
suck to have an ongoing exhaust leak. Also just remember to poke your head under every so often maybe every time you stop etc, just to check it's not fallen apart again. I remember not long after fitting mine seeing this beamer driving along with its exhaust bouncing up and down as it dragged along the ground, funny to think of on a beamer.
_________________ Signature removed by moderator.signature must not exceed 120x500 pixles |
|||
| Top | |
|||
| clampy |
|
||
|
yeah its just a pain in the a**..... crap way to spend a day off taking it in on a monday oh well
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| Krytox |
|
|||
|
few fixes:
return it. or Lightly grind the bolt hole flanges, this helps to pull the joins together. I've even used 2 gaskets and stag in some cases.
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| clampy |
|
||
|
nah the old coon going back in.... they should fix it
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| clampy |
|
||
|
what type of material should i use for a gasket for flanges between the extractors and cat i have some thing called gaskoid its like cardboard can i use that????
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| clampy |
|
||
|
ok alll done made the gasket me self ..... took it apart and did it my self ,2 of the bolts were lose so thats y the gasket blew out so should be all good now started and sounds good...
the extractors warm up pretty quick is this normal or am i worrying over nothing
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| PIMP_LTD |
|
||
|
clampy wrote: the extractors warm up pretty quick is this normal or am i worrying over nothing LOLOL, perfectly normal mate.
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| KWIKXR |
|
|||
|
PIMP_LTD wrote: clampy wrote: the extractors warm up pretty quick is this normal or am i worrying over nothing LOLOL, perfectly normal mate. Very normal, they're bare pipes so the exhuast gases will heat them up fast. Wouldnt of noticed it much before because of the heat shield but yeah its normal. My extractors warm up very quick, sometimes i think mine are on the verge of glowing 
|
|||
| Top | |
|||
| creeture3 |
|
||
|
I've never used gaskets on zorsts, only silicon. Works a treat and bends to any shape and fills gaps really well
|
||
| Top | |
||
| clampy |
|
||
|
ok i used a gasket and silcon goes good..
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| clampy |
|
||
|
how can i check for an exhaust leak???
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| XRfairmont67 |
|
|||
|
get someone to help u, put a rag over the tip and have the other person hold it there while you start it up, then u have a listen underneath
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 99 guests |
