|
| Falcon96XR6 |
|
|||
|
Hi all, I'm in the middle of a head gasket replacement, I've bought a genuine ford au mls gasket for my el xr6, although didn't come with the torque stages, I have rang ford and they reckon they can't find their torque specs etc, so they're no help, and they directed me to southern engine reconditioning so I called them, and told them I had a au mls gasket and they told me 30 foot pound first stage, then an extra 90 degrees for the second stage, but I converted the 30 foot pound and its 40nm, I was under the impression that torque setting is for composite gaskets and au mls ones were 30nm then 120 degrees? I just want some sturdy info before I put the head back on and not need to worry about it, thank you
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| TimmyA |
|
|||
|
Hey Mate,
Yeah my ED book says 40Nm + 90deg while the AU book says 30Nm + 120deg... Both of which were genuine ford books... When I did my VCT I did the bolts to 30+120... Cheers, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
Ohkay, and have had no dramas?
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| TimmyA |
|
|||
|
Did the first time... Long story... In my build thread... But not since the new mls and head bolts done to 30+120
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| Falcon96XR6 |
|
|||
|
Okay, haha cheers
_________________ EL XR6, T5 Speed - Full Factory Fitted Tickford Body Kit, AU Engine, Billet Camtech 845 Cam, J3 Chip, MLS Gasket, Intake, Extractors, High flow cat, 2 1/2in exhaust, K&N Air Filter, 3.45 LSD, - My Pride and Joy |
|||
| Top | |
|||
| TimmyA |
|
|||
|
Feel free to read it... Linked in my signature below... Contents Page at the start to help you find it...
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| phongus |
|
|||
|
40Nm + 90deg = E-series composite head gasket
30Nm + 120deg = AU MLS head gasket Well that's what I think it means.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| snap0964 |
|
|||
|
The Ford person must've been lazy, the reco mob - I wonder what sort of work they're putting out.
Use the torque settings for the particular gasket - usually in the packaging. In this case, AU settings as they're the official specs for that gasket. There's plenty of head gasket threads here - some good explanations on the torque setting as well as why angular settings are used as well as a 2nd stage.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 72 guests |
